89 lines
2.6 KiB
Plaintext
89 lines
2.6 KiB
Plaintext
#
|
|
# Freescale device configuration
|
|
#
|
|
|
|
config NET_VENDOR_FREESCALE
|
|
bool "Freescale devices"
|
|
default y
|
|
depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
|
|
M523x || M527x || M5272 || M528x || M520x || M532x || \
|
|
ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
|
|
---help---
|
|
If you have a network (Ethernet) card belonging to this class, say Y
|
|
and read the Ethernet-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about Freescale devices. If you say Y, you will be
|
|
asked for your specific card in the following questions.
|
|
|
|
if NET_VENDOR_FREESCALE
|
|
|
|
config FEC
|
|
tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
|
|
depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
|
|
ARCH_MXC || SOC_IMX28)
|
|
default ARCH_MXC || SOC_IMX28 if ARM
|
|
select PHYLIB
|
|
---help---
|
|
Say Y here if you want to use the built-in 10/100 Fast ethernet
|
|
controller on some Motorola ColdFire and Freescale i.MX processors.
|
|
|
|
config FEC_MPC52xx
|
|
tristate "FEC MPC52xx driver"
|
|
depends on PPC_MPC52xx && PPC_BESTCOMM
|
|
select CRC32
|
|
select PHYLIB
|
|
select PPC_BESTCOMM_FEC
|
|
---help---
|
|
This option enables support for the MPC5200's on-chip
|
|
Fast Ethernet Controller
|
|
If compiled as module, it will be called fec_mpc52xx.
|
|
|
|
config FEC_MPC52xx_MDIO
|
|
bool "FEC MPC52xx MDIO bus driver"
|
|
depends on FEC_MPC52xx
|
|
default y
|
|
---help---
|
|
The MPC5200's FEC can connect to the Ethernet either with
|
|
an external MII PHY chip or 10 Mbps 7-wire interface
|
|
(Motorola? industry standard).
|
|
If your board uses an external PHY connected to FEC, enable this.
|
|
If not sure, enable.
|
|
If compiled as module, it will be called fec_mpc52xx_phy.
|
|
|
|
source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
|
|
|
|
config FSL_PQ_MDIO
|
|
tristate "Freescale PQ MDIO"
|
|
depends on FSL_SOC
|
|
select PHYLIB
|
|
---help---
|
|
This driver supports the MDIO bus used by the gianfar and UCC drivers.
|
|
|
|
config UCC_GETH
|
|
tristate "Freescale QE Gigabit Ethernet"
|
|
depends on QUICC_ENGINE
|
|
select FSL_PQ_MDIO
|
|
select PHYLIB
|
|
---help---
|
|
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
|
|
which is available on some Freescale SOCs.
|
|
|
|
config UGETH_TX_ON_DEMAND
|
|
bool "Transmit on Demand support"
|
|
depends on UCC_GETH
|
|
|
|
config GIANFAR
|
|
tristate "Gianfar Ethernet"
|
|
depends on FSL_SOC
|
|
select FSL_PQ_MDIO
|
|
select PHYLIB
|
|
select CRC32
|
|
---help---
|
|
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
|
|
and MPC86xx family of chips, and the FEC on the 8540.
|
|
|
|
endif # NET_VENDOR_FREESCALE
|