64 lines
2.7 KiB
Plaintext
64 lines
2.7 KiB
Plaintext
Qualcomm's TSENS driver
|
|
|
|
The TSENS driver supports reading temperature from sensors across
|
|
the MSM. The driver defaults to support a 10 bit ADC.
|
|
|
|
The driver uses the Thermal sysfs framework to provide thermal
|
|
clients the ability to enable/disable the sensors, read trip zones,
|
|
read cool/warm temperature thresholds, set temperature thresholds
|
|
for cool/warm notification and receive notification on temperature
|
|
threshold events.
|
|
|
|
TSENS node
|
|
|
|
Required properties:
|
|
- compatible : should be "qcom,msm-tsens" for MSM8974 TSENS driver.
|
|
- reg : offset and length of the TSENS registers.
|
|
- reg : offset and length of the QFPROM registers used for storing
|
|
the calibration data for the individual sensors.
|
|
- reg-names : resource names used for the physical address of the TSENS
|
|
registers, the QFPROM efuse primary calibration address region,
|
|
Should be "tsens_physical" for physical address of the TSENS,
|
|
"tsens_eeprom_physical" for physical address where primary
|
|
calibration data is stored. This includes the backup
|
|
calibration address region if TSENS calibration data is stored
|
|
in the region.
|
|
- interrupts : TSENS interrupt for cool/warm temperature threshold.
|
|
- qcom,sensors : Total number of available Temperature sensors for TSENS.
|
|
- qcom,slope : One point calibration characterized slope data for each
|
|
sensor used to compute the offset. Slope is represented
|
|
as ADC code/DegC and the value is multipled by a factor
|
|
of 1000.
|
|
- qcom,calib-mode : Calibration masks to use to abstract the offset data from efuse.
|
|
Select from the following strings.
|
|
"fuse_map1" : Used for 8974/9x25 fuse calibration map.
|
|
"fuse_map2" : Used for 8x26 fuse calibration map.
|
|
"fuse_map3" : Used for 8x10 fuse calibration map.
|
|
|
|
Optional properties:
|
|
- qcom,calibration-less-mode : If present the pre-characterized data for offsets
|
|
are used else it defaults to use calibration data from QFPROM.
|
|
- qcom,tsens-local-init : If the flag is present the TSENS control registers are
|
|
initialized. If the boot configures the control register there is
|
|
no need to re-initialize them. The control registers are also
|
|
under a secure domain which can prevent them from being initialized
|
|
locally.
|
|
- qcom,sensor-id : If the flag is present map the TSENS sensors based on the
|
|
remote sensors that are enabled in HW. Ensure the mapping is not
|
|
more than the number of supported sensors.
|
|
Example:
|
|
|
|
tsens@fc4a8000 {
|
|
compatible = "qcom,msm-tsens";
|
|
reg = <0xfc4a8000 0x2000>,
|
|
<0xfc4b8000 0x1000>;
|
|
reg-names = "tsens_physical",
|
|
"tsens_eeprom_physical";
|
|
interrupts = <0 184 0>;
|
|
qcom,calibration-less-mode;
|
|
qcom,sensors = <11>;
|
|
qcom,slope = <3200 3200 3200 3200 3200 3200 3200 3200 3200
|
|
3200>;
|
|
qcom,calib-mode = "fuse_map1";
|
|
};
|