128 lines
5.1 KiB
Plaintext
128 lines
5.1 KiB
Plaintext
Device State Configuration Registers
|
|
------------------------------------
|
|
|
|
TI C6X SoCs contain a region of miscellaneous registers which provide various
|
|
function for SoC control or status. Details vary considerably among from SoC
|
|
to SoC with no two being alike.
|
|
|
|
In general, the Device State Configuraion Registers (DSCR) will provide one or
|
|
more configuration registers often protected by a lock register where one or
|
|
more key values must be written to a lock register in order to unlock the
|
|
configuration register for writes. These configuration register may be used to
|
|
enable (and disable in some cases) SoC pin drivers, select peripheral clock
|
|
sources (internal or pin), etc. In some cases, a configuration register is
|
|
write once or the individual bits are write once. In addition to device config,
|
|
the DSCR block may provide registers which which are used to reset peripherals,
|
|
provide device ID information, provide ethernet MAC addresses, as well as other
|
|
miscellaneous functions.
|
|
|
|
For device state control (enable/disable), each device control is assigned an
|
|
id which is used by individual device drivers to control the state as needed.
|
|
|
|
Required properties:
|
|
|
|
- compatible: must be "ti,c64x+dscr"
|
|
- reg: register area base and size
|
|
|
|
Optional properties:
|
|
|
|
NOTE: These are optional in that not all SoCs will have all properties. For
|
|
SoCs which do support a given property, leaving the property out of the
|
|
device tree will result in reduced functionality or possibly driver
|
|
failure.
|
|
|
|
- ti,dscr-devstat
|
|
offset of the devstat register
|
|
|
|
- ti,dscr-silicon-rev
|
|
offset, start bit, and bitsize of silicon revision field
|
|
|
|
- ti,dscr-rmii-resets
|
|
offset and bitmask of RMII reset field. May have multiple tuples if more
|
|
than one ethernet port is available.
|
|
|
|
- ti,dscr-locked-regs
|
|
possibly multiple tuples describing registers which are write protected by
|
|
a lock register. Each tuple consists of the register offset, lock register
|
|
offsset, and the key value used to unlock the register.
|
|
|
|
- ti,dscr-kick-regs
|
|
offset and key values of two "kick" registers used to write protect other
|
|
registers in DSCR. On SoCs using kick registers, the first key must be
|
|
written to the first kick register and the second key must be written to
|
|
the second register before other registers in the area are write-enabled.
|
|
|
|
- ti,dscr-mac-fuse-regs
|
|
MAC addresses are contained in two registers. Each element of a MAC address
|
|
is contained in a single byte. This property has two tuples. Each tuple has
|
|
a register offset and four cells representing bytes in the register from
|
|
most significant to least. The value of these four cells is the MAC byte
|
|
index (1-6) of the byte within the register. A value of 0 means the byte
|
|
is unused in the MAC address.
|
|
|
|
- ti,dscr-devstate-ctl-regs
|
|
This property describes the bitfields used to control the state of devices.
|
|
Each tuple describes a range of identical bitfields used to control one or
|
|
more devices (one bitfield per device). The layout of each tuple is:
|
|
|
|
start_id num_ids reg enable disable start_bit nbits
|
|
|
|
Where:
|
|
start_id is device id for the first device control in the range
|
|
num_ids is the number of device controls in the range
|
|
reg is the offset of the register holding the control bits
|
|
enable is the value to enable a device
|
|
disable is the value to disable a device (0xffffffff if cannot disable)
|
|
start_bit is the bit number of the first bit in the range
|
|
nbits is the number of bits per device control
|
|
|
|
- ti,dscr-devstate-stat-regs
|
|
This property describes the bitfields used to provide device state status
|
|
for device states controlled by the DSCR. Each tuple describes a range of
|
|
identical bitfields used to provide status for one or more devices (one
|
|
bitfield per device). The layout of each tuple is:
|
|
|
|
start_id num_ids reg enable disable start_bit nbits
|
|
|
|
Where:
|
|
start_id is device id for the first device status in the range
|
|
num_ids is the number of devices covered by the range
|
|
reg is the offset of the register holding the status bits
|
|
enable is the value indicating device is enabled
|
|
disable is the value indicating device is disabled
|
|
start_bit is the bit number of the first bit in the range
|
|
nbits is the number of bits per device status
|
|
|
|
- ti,dscr-privperm
|
|
Offset and default value for register used to set access privilege for
|
|
some SoC devices.
|
|
|
|
|
|
Example:
|
|
|
|
device-state-config-regs@2a80000 {
|
|
compatible = "ti,c64x+dscr";
|
|
reg = <0x02a80000 0x41000>;
|
|
|
|
ti,dscr-devstat = <0>;
|
|
ti,dscr-silicon-rev = <8 28 0xf>;
|
|
ti,dscr-rmii-resets = <0x40020 0x00040000>;
|
|
|
|
ti,dscr-locked-regs = <0x40008 0x40004 0x0f0a0b00>;
|
|
ti,dscr-devstate-ctl-regs =
|
|
<0 12 0x40008 1 0 0 2
|
|
12 1 0x40008 3 0 30 2
|
|
13 2 0x4002c 1 0xffffffff 0 1>;
|
|
ti,dscr-devstate-stat-regs =
|
|
<0 10 0x40014 1 0 0 3
|
|
10 2 0x40018 1 0 0 3>;
|
|
|
|
ti,dscr-mac-fuse-regs = <0x700 1 2 3 4
|
|
0x704 5 6 0 0>;
|
|
|
|
ti,dscr-privperm = <0x41c 0xaaaaaaaa>;
|
|
|
|
ti,dscr-kick-regs = <0x38 0x83E70B13
|
|
0x3c 0x95A4F1E0>;
|
|
};
|