596 lines
12 KiB
INI
Executable File
596 lines
12 KiB
INI
Executable File
# This file allows user to override the factory
|
|
|
|
# defaults for the WLAN Driver
|
|
|
|
|
|
# Enable IMPS or not
|
|
gEnableImps=1
|
|
|
|
# Enable/Disable Idle Scan
|
|
|
|
gEnableIdleScan=0
|
|
|
|
|
|
# Increase sleep duration (seconds) during IMPS
|
|
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
|
|
# unnecessary if Idle Scan is disabled.
|
|
gImpsModSleepTime=0
|
|
|
|
|
|
# Enable BMPS or not
|
|
gEnableBmps=1
|
|
|
|
# Enable suspend or not
|
|
|
|
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
|
|
|
|
gEnableSuspend=3
|
|
|
|
|
|
# Phy Mode (auto, b, g, n, etc)
|
|
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
|
|
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
|
|
# 7 = 11b only 8 = 11ac only.
|
|
gDot11Mode=0
|
|
|
|
|
|
# CSR Roaming Enable(1) Disable(0)
|
|
|
|
gRoamingTime=0
|
|
|
|
|
|
# Assigned MAC Addresses - This will be used until NV items are in place
|
|
|
|
# Each byte of MAC address is represented in Hex format as XX
|
|
|
|
Intf0MacAddress=000AF58989FF
|
|
Intf1MacAddress=000AF58989FE
|
|
Intf2MacAddress=000AF58989FD
|
|
|
|
Intf3MacAddress=000AF58989FC
|
|
|
|
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
|
|
|
InfraUapsdVoSrvIntv=0
|
|
|
|
InfraUapsdViSrvIntv=0
|
|
|
|
InfraUapsdBeSrvIntv=0
|
|
|
|
InfraUapsdBkSrvIntv=0
|
|
|
|
# Flag to allow STA send AddTspec even when ACM is Off
|
|
gAddTSWhenACMIsOff=1
|
|
|
|
# Make 1x1 the default antenna configuration
|
|
|
|
gNumRxAnt=1
|
|
|
|
|
|
# Beacon filtering frequency (unit in beacon intervals)
|
|
|
|
gNthBeaconFilter=50
|
|
|
|
|
|
# Enable WAPI or not
|
|
|
|
# WAPIIsEnabled=0
|
|
|
|
|
|
# Flags to filter Mcast abd Bcast RX packets.
|
|
|
|
# Value 0: No filtering, 1: Filter all Multicast.
|
|
|
|
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
|
|
|
|
McastBcastFilter=3
|
|
|
|
|
|
#Flag to enable HostARPOffload feature or not
|
|
|
|
hostArpOffload=1
|
|
|
|
#Flag to enable TCPChkSumOffld feature or not
|
|
|
|
gEnableTCPChkSumOffld=0
|
|
|
|
#Flag to enable HostNSOffload feature or not
|
|
|
|
hostNSOffload=1
|
|
|
|
#Flag to enable IPChkSumOffld feature or not
|
|
|
|
gEnableIPChecksumOffload=0
|
|
|
|
#SoftAP Related Parameters
|
|
|
|
# AP MAc addr
|
|
|
|
gAPMacAddr=000AF589dcab
|
|
|
|
|
|
# 802.11n Protection flag
|
|
|
|
gEnableApProt=1
|
|
|
|
|
|
#Enable OBSS protection
|
|
|
|
gEnableApOBSSProt=1
|
|
|
|
|
|
#Enable/Disable UAPSD for SoftAP
|
|
|
|
gEnableApUapsd=1
|
|
|
|
|
|
# Fixed Rate
|
|
|
|
gFixedRate=0
|
|
|
|
|
|
# Maximum Tx power
|
|
|
|
# gTxPowerCap=30
|
|
|
|
|
|
# Fragmentation Threshold
|
|
|
|
# gFragmentationThreshold=2346
|
|
|
|
|
|
# RTS threshold
|
|
|
|
RTSThreshold=1048576
|
|
|
|
|
|
# Intra-BSS forward
|
|
|
|
gDisableIntraBssFwd=0
|
|
|
|
|
|
# WMM Enable/Disable
|
|
|
|
WmmIsEnabled=0
|
|
|
|
|
|
# 802.11d support
|
|
|
|
g11dSupportEnabled=0
|
|
|
|
# 802.11h support
|
|
|
|
g11hSupportEnabled=1
|
|
|
|
# DFS Master Capability
|
|
gEnableDFSMasterCap=1
|
|
|
|
# ESE Support and fast transition
|
|
EseEnabled=0
|
|
ImplicitQosIsEnabled=0
|
|
gNeighborScanTimerPeriod=200
|
|
|
|
gNeighborLookupThreshold=76
|
|
gNeighborReassocThreshold=81
|
|
|
|
gNeighborScanChannelMinTime=20
|
|
gNeighborScanChannelMaxTime=30
|
|
gMaxNeighborReqTries=3
|
|
|
|
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
|
# To enable, set FastRoamEnabled=1
|
|
# To disable, set FastRoamEnabled=0
|
|
FastRoamEnabled=1
|
|
|
|
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
|
|
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
|
|
#the RSSI of the new/roamable AP should be for roaming
|
|
RoamRssiDiff=3
|
|
|
|
# If the RSSI of any available candidate is better than currently associated
|
|
# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
|
|
# registering for reassoc threshold).
|
|
# NOTE: Value of 0 means that we would register for reassoc threshold.
|
|
gImmediateRoamRssiDiff=10
|
|
|
|
# To enable, set gRoamIntraBand=1 (Roaming within band)
|
|
# To disable, set gRoamIntraBand=0 (Roaming across band)
|
|
gRoamIntraBand=0
|
|
|
|
# SAP Country code
|
|
|
|
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
|
|
|
|
# Example
|
|
|
|
# US Indoor, USI
|
|
|
|
# Korea Outdoor, KRO
|
|
|
|
# Japan without optional byte, JP
|
|
|
|
# France without optional byte, FR
|
|
|
|
#gAPCntryCode=USI
|
|
|
|
|
|
#Short Guard Interval Enable/disable
|
|
|
|
gShortGI20Mhz=1
|
|
|
|
gShortGI40Mhz=1
|
|
|
|
|
|
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
|
|
|
|
gAPAutoShutOff=0
|
|
|
|
#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
|
|
gWlanAutoShutdown = 0
|
|
|
|
|
|
# Listen Energy Detect Mode Configuration
|
|
|
|
# Valid values 0-128
|
|
|
|
# 128 means disable Energy Detect feature
|
|
|
|
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
|
|
|
|
# 10-128 are reserved.
|
|
|
|
# The EDET threshold mapping is as follows in 3dB step:
|
|
|
|
# 0 = -60 dBm
|
|
|
|
# 1 = -63 dBm
|
|
|
|
# 2 = -66 dBm
|
|
|
|
# ...
|
|
|
|
# 7 = -81 dBm
|
|
|
|
# 8 = -84 dBm
|
|
|
|
# 9 = -87 dBm
|
|
|
|
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
|
|
|
|
#
|
|
|
|
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
|
|
|
|
#
|
|
|
|
gEnablePhyAgcListenMode=128
|
|
|
|
|
|
#Preferred band (both or 2.4 only or 5 only)
|
|
|
|
BandCapability=0
|
|
|
|
|
|
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
|
|
|
|
enableBeaconEarlyTermination=0
|
|
|
|
beaconEarlyTerminationWakeInterval=3
|
|
|
|
|
|
#Channel Bonding
|
|
gChannelBondingMode5GHz=1
|
|
gChannelBondingMode24GHz=0
|
|
|
|
|
|
#Enable Keep alive with non-zero period value
|
|
|
|
gStaKeepAlivePeriod = 30
|
|
|
|
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
|
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
|
|
#For both active and power save clients.
|
|
|
|
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
|
|
#If doesn't honor for 5 seconds then DUT remove client.
|
|
|
|
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
|
|
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
|
|
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
|
|
|
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
|
|
#where we send NULL frame.
|
|
|
|
#gApLinkMonitorPeriod = 10
|
|
|
|
#gGoLinkMonitorPeriod = 10
|
|
|
|
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
|
|
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
|
|
|
|
|
|
gGoKeepAlivePeriod = 20
|
|
|
|
gApKeepAlivePeriod = 20
|
|
|
|
|
|
#If set will start with active scan after driver load, otherwise will start with
|
|
|
|
#passive scan to find out the domain
|
|
|
|
gEnableBypass11d=1
|
|
|
|
|
|
#If set to 0, will not scan DFS channels
|
|
|
|
gEnableDFSChnlScan=1
|
|
|
|
|
|
gVhtChannelWidth=2
|
|
gEnableLogp=1
|
|
|
|
|
|
# Enable Automatic Tx Power control
|
|
|
|
gEnableAutomaticTxPowerControl=1
|
|
|
|
# 0 for OLPC 1 for CLPC and SCPC
|
|
gEnableCloseLoop=1
|
|
|
|
#Data Inactivity Timeout when in powersave (in ms)
|
|
gDataInactivityTimeout=200
|
|
|
|
# VHT Tx/Rx MCS values
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gVhtRxMCS=2
|
|
gVhtTxMCS=2
|
|
|
|
# VHT Tx/Rx MCS values for 2x2
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gEnable2x2=1
|
|
gVhtRxMCS2x2=2
|
|
gVhtTxMCS2x2=2
|
|
|
|
# Enable Tx beamforming
|
|
gTxBFEnable=0
|
|
|
|
# Enable Tx beamforming in VHT20MHz
|
|
# Valid values are 0,1. If commented out, the default value is 0.
|
|
# 0=disable, 1=enable
|
|
gEnableTxBFin20MHz=0
|
|
|
|
# Set txchainmask and rxchainmask
|
|
# These parameters are used only if gEnable2x2 is 0
|
|
# Valid values are 1,2
|
|
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
|
|
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
|
|
gSetTxChainmask1x1=1
|
|
gSetRxChainmask1x1=1
|
|
|
|
# Scan Timing Parameters
|
|
# gPassiveMaxChannelTime=110
|
|
# gPassiveMinChannelTime=60
|
|
gActiveMaxChannelTime=80
|
|
gActiveMinChannelTime=40
|
|
|
|
#If set to 0, MCC is not allowed.
|
|
gEnableMCCMode=1
|
|
|
|
# MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band
|
|
gWlanMccToSccSwitchMode = 0
|
|
|
|
# 1=enable STBC; 0=disable STBC
|
|
gEnableRXSTBC=1
|
|
|
|
# 1=enable tx STBC; 0=disable
|
|
gEnableTXSTBC=1
|
|
|
|
# 1=enable rx LDPC; 0=disable
|
|
gEnableRXLDPC=1
|
|
|
|
# Enable Active mode offload
|
|
gEnableActiveModeOffload=1
|
|
|
|
#Enable Scan Results Aging based on timer
|
|
#Timer value is in seconds
|
|
#If Set to 0 it will not enable the feature
|
|
gScanAgingTime=0
|
|
|
|
#Enable Scan Results Aging based on number of scans
|
|
gScanResultAgeCount=1
|
|
|
|
#Enable Power saving mechanism Based on Android Framework
|
|
#If set to 0 Driver internally control the Power saving mechanism
|
|
#If set to 1 Android Framwrok control the Power saving mechanism
|
|
isAndroidPsEn=0
|
|
|
|
#Enable thermal mitigation
|
|
gThermalMitigationEnable=0
|
|
|
|
gEnableFastRoamInConcurrency=1
|
|
|
|
#List of Country codes for which 11ac needs to be disabled
|
|
#Each country code must be delimited by comma(,)
|
|
gListOfNon11acCountryCode=RU,UA,ZA
|
|
|
|
#Maxium Channel time in msec
|
|
gMaxMediumTime = 6000
|
|
|
|
# 802.11K support
|
|
gRrmEnable=1
|
|
gRrmOperChanMax=8
|
|
gRrmNonOperChanMax=8
|
|
gRrmRandIntvl=100
|
|
|
|
#Scan offload
|
|
gEnableDirectedScanOffload=1
|
|
|
|
#FlexConnect Power Factor
|
|
#Default is set to 0 (disable)
|
|
gFlexConnectPowerFactor=0
|
|
|
|
#Disable split scan, the FW will take care of it
|
|
gNumChanCombinedConc=60
|
|
|
|
#Enable Power Save offload
|
|
gEnablePowerSaveOffload=1
|
|
|
|
#Enable firmware uart print
|
|
gEnablefwprint=0
|
|
|
|
#Enable firmware log
|
|
gEnablefwlog=1
|
|
|
|
|
|
#IPA config is a bit mask and following are the configurations.
|
|
#bit0 IPA Enable
|
|
#bit1 IPA PRE Filter enable
|
|
#bit2 IPv6 enable
|
|
#bit3 IPA Resource Manager (RM) enable
|
|
#bit4 IPA Clock scaling enable
|
|
gIPAConfig=0x1d
|
|
gIPADescSize=1600
|
|
|
|
#P2P Listen offload
|
|
gEnableP2pListenOffload=1
|
|
|
|
# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k)
|
|
gVhtAmpduLenExponent=7
|
|
|
|
# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets)
|
|
gVhtMpduLen=2
|
|
|
|
# Maximum number of wow filters required
|
|
#gMaxWoWFilters=22
|
|
|
|
# WOW Enable/Disable.
|
|
# 0 - Disable both magic pattern match and pattern byte match.
|
|
# 1 - Enable magic pattern match on all interfaces.
|
|
# 2 - Enable pattern byte match on all interfaces.
|
|
# 3 - Enable both magic patter and pattern byte match on all interfaces.
|
|
# Default value of gEnableWoW is 3.
|
|
# gEnableWoW=0
|
|
|
|
# Enable or Disable MCC Adaptive Scheduler at the FW
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMCCAdaptiveScheduler=0
|
|
|
|
#Enable or Disable p2p device address administered
|
|
isP2pDeviceAddrAdministrated=0
|
|
|
|
#Enable Rx thread
|
|
gEnableRxThread=0
|
|
|
|
# Set Thermal Power limit
|
|
TxPower2g=10
|
|
TxPower5g=10
|
|
|
|
# Remove Overlap channel restriction
|
|
gEnableOverLapCh=0
|
|
|
|
# VHT is not supported for 2.4 G
|
|
gEnableVhtFor24GHzBand=0
|
|
|
|
#Enable or Disable 5G early beacon termination
|
|
gEnable5gEBT=1
|
|
|
|
#Maximum number of offload peers supported
|
|
gMaxOffloadPeers=5
|
|
|
|
# controlling the following offload patterns
|
|
# through ini parameter. Default value is 1
|
|
# to disable set it to zero. ssdp = 0
|
|
# Setup multicast pattern for mDNS 224.0.0.251,
|
|
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
|
|
ssdp = 0
|
|
|
|
#Enable Hysteretic mode
|
|
gEnableHystereticMode=1
|
|
|
|
#Disable/Enable Strict FCC Regulatory
|
|
# 0 to disable, 1 to enable
|
|
gEnableStrictRegulatoryForFCC=0
|
|
|
|
#Disable packet log feature
|
|
gEnablePacketLog=0
|
|
|
|
# Bus bandwidth threshold values in terms of number of packets
|
|
gBusBandwidthHighThreshold=40000
|
|
gBusBandwidthMediumThreshold=10000
|
|
gBusBandwidthLowThreshold=3000
|
|
|
|
# Bus bandwidth compute timeout value in ms
|
|
gBusBandwidthComputeInterval=3000
|
|
|
|
# Bandwidth setting for IPA clock scailing
|
|
gIPAHighBandwidthMbps=800
|
|
gIPAMediumBandwidthMbps=400
|
|
gIPALowBandwidthMbps=100
|
|
|
|
# Regulatory Setting; 0=STRICT; 1=CUSTOM
|
|
gRegulatoryChangeCountry=1
|
|
# RA filtering rate limit param, the current value would not
|
|
# help if the lifetime in RA is less than 3*60=3min. Then
|
|
# we need to change it, though it is uncommon.
|
|
# gRAFilterEnable=0
|
|
gRArateLimitInterval=60
|
|
|
|
# Maximum number of concurrent connections
|
|
gMaxConcurrentActiveSessions=2
|
|
|
|
# Disable/Enable GreenAP
|
|
# 0 to disable, 1 to enable, default: 1
|
|
gEnableGreenAp=1
|
|
|
|
# Radar PRI multiplier
|
|
gDFSradarMappingPriMultiplier=4
|
|
|
|
gPNOScanSupport=0
|
|
|
|
# Enable/Disable RX full reorder offload
|
|
gReorderOffloadSupported=1
|
|
|
|
#Enable/Disable LPASS support
|
|
# 0 to disable, 1 to enable
|
|
gEnableLpassSupport=0
|
|
|
|
# Whether userspace country code setting shld have priority
|
|
gCountryCodePriority=1
|
|
|
|
# Enable(1)/Disable(0) SIFS burst
|
|
gEnableSifsBurst=1
|
|
|
|
# Enable or Disable Multi-user MIMO
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMuBformee=1
|
|
|
|
# Enable/Disable channel avoidance for SAP in SCC scenario
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gSapSccChanAvoidance=1
|
|
|
|
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
|
|
gIbssTxSpEndInactivityTime=0
|
|
|
|
# Enable/Disable IPA uC offload
|
|
IpaUcOffloadEnabled=1
|
|
# Enable/Disable IPA uC offload in concurrent mode
|
|
gIpaUcStaOffload=1
|
|
|
|
#Enable DFS phyerrors filtering offload
|
|
dfsPhyerrFilterOffload=1
|
|
|
|
# Driver force 11AC override for SAP/Go
|
|
gAP11ACOverride=0
|
|
|
|
# Enable broadcast logging to the userspace entities
|
|
gMulticastHostFwMsgs=0
|
|
|
|
END
|
|
|
|
# Note: Configuration parser would not read anything past the END marker
|
|
|