M7350/kernel/drivers/ata/pata_amd.c
2024-09-09 08:57:42 +00:00

641 lines
17 KiB
C

/*
* pata_amd.c - AMD PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
*
* Based on pata-sil680. Errata information is taken from data sheets
* and the amd74xx.c driver by Vojtech Pavlik. Nvidia SATA devices are
* claimed by sata-nv.c.
*
* TODO:
* Variable system clock when/if it makes sense
* Power management on ports
*
*
* Documentation publicly available.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_amd"
#define DRV_VERSION "0.4.1"
/**
* timing_setup - shared timing computation and load
* @ap: ATA port being set up
* @adev: drive being configured
* @offset: port offset
* @speed: target speed
* @clock: clock multiplier (number of times 33MHz for this part)
*
* Perform the actual timing set up for Nvidia or AMD PATA devices.
* The actual devices vary so they all call into this helper function
* providing the clock multipler and offset (because AMD and Nvidia put
* the ports at different locations).
*/
static void timing_setup(struct ata_port *ap, struct ata_device *adev, int offset, int speed, int clock)
{
static const unsigned char amd_cyc2udma[] = {
6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_device *peer = ata_dev_pair(adev);
int dn = ap->port_no * 2 + adev->devno;
struct ata_timing at, apeer;
int T, UT;
const int amd_clock = 33333; /* KHz. */
u8 t;
T = 1000000000 / amd_clock;
UT = T;
if (clock >= 2)
UT = T / 2;
if (ata_timing_compute(adev, speed, &at, T, UT) < 0) {
dev_err(&pdev->dev, "unknown mode %d\n", speed);
return;
}
if (peer) {
/* This may be over conservative */
if (peer->dma_mode) {
ata_timing_compute(peer, peer->dma_mode, &apeer, T, UT);
ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT);
}
ata_timing_compute(peer, peer->pio_mode, &apeer, T, UT);
ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT);
}
if (speed == XFER_UDMA_5 && amd_clock <= 33333) at.udma = 1;
if (speed == XFER_UDMA_6 && amd_clock <= 33333) at.udma = 15;
/*
* Now do the setup work
*/
/* Configure the address set up timing */
pci_read_config_byte(pdev, offset + 0x0C, &t);
t = (t & ~(3 << ((3 - dn) << 1))) | ((clamp_val(at.setup, 1, 4) - 1) << ((3 - dn) << 1));
pci_write_config_byte(pdev, offset + 0x0C , t);
/* Configure the 8bit I/O timing */
pci_write_config_byte(pdev, offset + 0x0E + (1 - (dn >> 1)),
((clamp_val(at.act8b, 1, 16) - 1) << 4) | (clamp_val(at.rec8b, 1, 16) - 1));
/* Drive timing */
pci_write_config_byte(pdev, offset + 0x08 + (3 - dn),
((clamp_val(at.active, 1, 16) - 1) << 4) | (clamp_val(at.recover, 1, 16) - 1));
switch (clock) {
case 1:
t = at.udma ? (0xc0 | (clamp_val(at.udma, 2, 5) - 2)) : 0x03;
break;
case 2:
t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 2, 10)]) : 0x03;
break;
case 3:
t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 1, 10)]) : 0x03;
break;
case 4:
t = at.udma ? (0xc0 | amd_cyc2udma[clamp_val(at.udma, 1, 15)]) : 0x03;
break;
default:
return;
}
/* UDMA timing */
if (at.udma)
pci_write_config_byte(pdev, offset + 0x10 + (3 - dn), t);
}
/**
* amd_pre_reset - perform reset handling
* @link: ATA link
* @deadline: deadline jiffies for the operation
*
* Reset sequence checking enable bits to see which ports are
* active.
*/
static int amd_pre_reset(struct ata_link *link, unsigned long deadline)
{
static const struct pci_bits amd_enable_bits[] = {
{ 0x40, 1, 0x02, 0x02 },
{ 0x40, 1, 0x01, 0x01 }
};
struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no]))
return -ENOENT;
return ata_sff_prereset(link, deadline);
}
/**
* amd_cable_detect - report cable type
* @ap: port
*
* AMD controller/BIOS setups record the cable type in word 0x42
*/
static int amd_cable_detect(struct ata_port *ap)
{
static const u32 bitmask[2] = {0x03, 0x0C};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 ata66;
pci_read_config_byte(pdev, 0x42, &ata66);
if (ata66 & bitmask[ap->port_no])
return ATA_CBL_PATA80;
return ATA_CBL_PATA40;
}
/**
* amd_fifo_setup - set the PIO FIFO for ATA/ATAPI
* @ap: ATA interface
* @adev: ATA device
*
* Set the PCI fifo for this device according to the devices present
* on the bus at this point in time. We need to turn the post write buffer
* off for ATAPI devices as we may need to issue a word sized write to the
* device as the final I/O
*/
static void amd_fifo_setup(struct ata_port *ap)
{
struct ata_device *adev;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static const u8 fifobit[2] = { 0xC0, 0x30};
u8 fifo = fifobit[ap->port_no];
u8 r;
ata_for_each_dev(adev, &ap->link, ENABLED) {
if (adev->class == ATA_DEV_ATAPI)
fifo = 0;
}
if (pdev->device == PCI_DEVICE_ID_AMD_VIPER_7411) /* FIFO is broken */
fifo = 0;
/* On the later chips the read prefetch bits become no-op bits */
pci_read_config_byte(pdev, 0x41, &r);
r &= ~fifobit[ap->port_no];
r |= fifo;
pci_write_config_byte(pdev, 0x41, r);
}
/**
* amd33_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the AMD registers for PIO mode.
*/
static void amd33_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
amd_fifo_setup(ap);
timing_setup(ap, adev, 0x40, adev->pio_mode, 1);
}
static void amd66_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
amd_fifo_setup(ap);
timing_setup(ap, adev, 0x40, adev->pio_mode, 2);
}
static void amd100_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
amd_fifo_setup(ap);
timing_setup(ap, adev, 0x40, adev->pio_mode, 3);
}
static void amd133_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
amd_fifo_setup(ap);
timing_setup(ap, adev, 0x40, adev->pio_mode, 4);
}
/**
* amd33_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the MWDMA/UDMA modes for the AMD and Nvidia
* chipset.
*/
static void amd33_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 1);
}
static void amd66_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 2);
}
static void amd100_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 3);
}
static void amd133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 4);
}
/* Both host-side and drive-side detection results are worthless on NV
* PATAs. Ignore them and just follow what BIOS configured. Both the
* current configuration in PCI config reg and ACPI GTM result are
* cached during driver attach and are consulted to select transfer
* mode.
*/
static unsigned long nv_mode_filter(struct ata_device *dev,
unsigned long xfer_mask)
{
static const unsigned int udma_mask_map[] =
{ ATA_UDMA2, ATA_UDMA1, ATA_UDMA0, 0,
ATA_UDMA3, ATA_UDMA4, ATA_UDMA5, ATA_UDMA6 };
struct ata_port *ap = dev->link->ap;
char acpi_str[32] = "";
u32 saved_udma, udma;
const struct ata_acpi_gtm *gtm;
unsigned long bios_limit = 0, acpi_limit = 0, limit;
/* find out what BIOS configured */
udma = saved_udma = (unsigned long)ap->host->private_data;
if (ap->port_no == 0)
udma >>= 16;
if (dev->devno == 0)
udma >>= 8;
if ((udma & 0xc0) == 0xc0)
bios_limit = ata_pack_xfermask(0, 0, udma_mask_map[udma & 0x7]);
/* consult ACPI GTM too */
gtm = ata_acpi_init_gtm(ap);
if (gtm) {
acpi_limit = ata_acpi_gtm_xfermask(dev, gtm);
snprintf(acpi_str, sizeof(acpi_str), " (%u:%u:0x%x)",
gtm->drive[0].dma, gtm->drive[1].dma, gtm->flags);
}
/* be optimistic, EH can take care of things if something goes wrong */
limit = bios_limit | acpi_limit;
/* If PIO or DMA isn't configured at all, don't limit. Let EH
* handle it.
*/
if (!(limit & ATA_MASK_PIO))
limit |= ATA_MASK_PIO;
if (!(limit & (ATA_MASK_MWDMA | ATA_MASK_UDMA)))
limit |= ATA_MASK_MWDMA | ATA_MASK_UDMA;
/* PIO4, MWDMA2, UDMA2 should always be supported regardless of
cable detection result */
limit |= ata_pack_xfermask(ATA_PIO4, ATA_MWDMA2, ATA_UDMA2);
ata_port_dbg(ap, "nv_mode_filter: 0x%lx&0x%lx->0x%lx, "
"BIOS=0x%lx (0x%x) ACPI=0x%lx%s\n",
xfer_mask, limit, xfer_mask & limit, bios_limit,
saved_udma, acpi_limit, acpi_str);
return xfer_mask & limit;
}
/**
* nv_probe_init - cable detection
* @lin: ATA link
*
* Perform cable detection. The BIOS stores this in PCI config
* space for us.
*/
static int nv_pre_reset(struct ata_link *link, unsigned long deadline)
{
static const struct pci_bits nv_enable_bits[] = {
{ 0x50, 1, 0x02, 0x02 },
{ 0x50, 1, 0x01, 0x01 }
};
struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (!pci_test_config_bits(pdev, &nv_enable_bits[ap->port_no]))
return -ENOENT;
return ata_sff_prereset(link, deadline);
}
/**
* nv100_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the AMD registers for PIO mode.
*/
static void nv100_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->pio_mode, 3);
}
static void nv133_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->pio_mode, 4);
}
/**
* nv100_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the MWDMA/UDMA modes for the AMD and Nvidia
* chipset.
*/
static void nv100_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->dma_mode, 3);
}
static void nv133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->dma_mode, 4);
}
static void nv_host_stop(struct ata_host *host)
{
u32 udma = (unsigned long)host->private_data;
/* restore PCI config register 0x60 */
pci_write_config_dword(to_pci_dev(host->dev), 0x60, udma);
}
static struct scsi_host_template amd_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
static const struct ata_port_operations amd_base_port_ops = {
.inherits = &ata_bmdma32_port_ops,
.prereset = amd_pre_reset,
};
static struct ata_port_operations amd33_port_ops = {
.inherits = &amd_base_port_ops,
.cable_detect = ata_cable_40wire,
.set_piomode = amd33_set_piomode,
.set_dmamode = amd33_set_dmamode,
};
static struct ata_port_operations amd66_port_ops = {
.inherits = &amd_base_port_ops,
.cable_detect = ata_cable_unknown,
.set_piomode = amd66_set_piomode,
.set_dmamode = amd66_set_dmamode,
};
static struct ata_port_operations amd100_port_ops = {
.inherits = &amd_base_port_ops,
.cable_detect = ata_cable_unknown,
.set_piomode = amd100_set_piomode,
.set_dmamode = amd100_set_dmamode,
};
static struct ata_port_operations amd133_port_ops = {
.inherits = &amd_base_port_ops,
.cable_detect = amd_cable_detect,
.set_piomode = amd133_set_piomode,
.set_dmamode = amd133_set_dmamode,
};
static const struct ata_port_operations nv_base_port_ops = {
.inherits = &ata_bmdma_port_ops,
.cable_detect = ata_cable_ignore,
.mode_filter = nv_mode_filter,
.prereset = nv_pre_reset,
.host_stop = nv_host_stop,
};
static struct ata_port_operations nv100_port_ops = {
.inherits = &nv_base_port_ops,
.set_piomode = nv100_set_piomode,
.set_dmamode = nv100_set_dmamode,
};
static struct ata_port_operations nv133_port_ops = {
.inherits = &nv_base_port_ops,
.set_piomode = nv133_set_piomode,
.set_dmamode = nv133_set_dmamode,
};
static void amd_clear_fifo(struct pci_dev *pdev)
{
u8 fifo;
/* Disable the FIFO, the FIFO logic will re-enable it as
appropriate */
pci_read_config_byte(pdev, 0x41, &fifo);
fifo &= 0x0F;
pci_write_config_byte(pdev, 0x41, fifo);
}
static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info[10] = {
{ /* 0: AMD 7401 - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
.port_ops = &amd33_port_ops
},
{ /* 1: Early AMD7409 - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &amd66_port_ops
},
{ /* 2: AMD 7409 */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &amd66_port_ops
},
{ /* 3: AMD 7411 */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &amd100_port_ops
},
{ /* 4: AMD 7441 */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &amd100_port_ops
},
{ /* 5: AMD 8111 - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &amd133_port_ops
},
{ /* 6: AMD 8111 UDMA 100 (Serenade) - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &amd133_port_ops
},
{ /* 7: Nvidia Nforce */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &nv100_port_ops
},
{ /* 8: Nvidia Nforce2 and later - no swdma */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &nv133_port_ops
},
{ /* 9: AMD CS5536 (Geode companion) */
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &amd100_port_ops
}
};
const struct ata_port_info *ppi[] = { NULL, NULL };
int type = id->driver_data;
void *hpriv = NULL;
u8 fifo;
int rc;
ata_print_version_once(&pdev->dev, DRV_VERSION);
rc = pcim_enable_device(pdev);
if (rc)
return rc;
pci_read_config_byte(pdev, 0x41, &fifo);
/* Check for AMD7409 without swdma errata and if found adjust type */
if (type == 1 && pdev->revision > 0x7)
type = 2;
/* Serenade ? */
if (type == 5 && pdev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
pdev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
type = 6; /* UDMA 100 only */
/*
* Okay, type is determined now. Apply type-specific workarounds.
*/
ppi[0] = &info[type];
if (type < 3)
ata_pci_bmdma_clear_simplex(pdev);
if (pdev->vendor == PCI_VENDOR_ID_AMD)
amd_clear_fifo(pdev);
/* Cable detection on Nvidia chips doesn't work too well,
* cache BIOS programmed UDMA mode.
*/
if (type == 7 || type == 8) {
u32 udma;
pci_read_config_dword(pdev, 0x60, &udma);
hpriv = (void *)(unsigned long)udma;
}
/* And fire it up */
return ata_pci_bmdma_init_one(pdev, ppi, &amd_sht, hpriv, 0);
}
#ifdef CONFIG_PM_SLEEP
static int amd_reinit_one(struct pci_dev *pdev)
{
struct ata_host *host = pci_get_drvdata(pdev);
int rc;
rc = ata_pci_device_do_resume(pdev);
if (rc)
return rc;
if (pdev->vendor == PCI_VENDOR_ID_AMD) {
amd_clear_fifo(pdev);
if (pdev->device == PCI_DEVICE_ID_AMD_VIPER_7409 ||
pdev->device == PCI_DEVICE_ID_AMD_COBRA_7401)
ata_pci_bmdma_clear_simplex(pdev);
}
ata_host_resume(host);
return 0;
}
#endif
static const struct pci_device_id amd[] = {
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_COBRA_7401), 0 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7409), 1 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_VIPER_7411), 3 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_OPUS_7441), 4 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_8111_IDE), 5 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE), 7 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE), 8 },
{ PCI_VDEVICE(NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE), 8 },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5536_IDE), 9 },
{ },
};
static struct pci_driver amd_pci_driver = {
.name = DRV_NAME,
.id_table = amd,
.probe = amd_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM_SLEEP
.suspend = ata_pci_device_suspend,
.resume = amd_reinit_one,
#endif
};
module_pci_driver(amd_pci_driver);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for AMD and Nvidia PATA IDE");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, amd);
MODULE_VERSION(DRV_VERSION);