99 lines
4.5 KiB
Plaintext
99 lines
4.5 KiB
Plaintext
* Qualcomm WCNSS Platform Driver
|
|
|
|
WCNSS driver is the platform driver. It is used for performing the cold
|
|
boot-up of the wireless device. It is responsible for adjusting
|
|
the necessary I/O rails and enabling appropriate gpios for wireless
|
|
connectivity subsystem.
|
|
|
|
Required properties:
|
|
- compatible: "wcnss_wlan"
|
|
- reg: physical address and length of the register set for the device.
|
|
- reg-names: "wcnss_mmio", "wcnss_fiq", "pronto_phy_base", "riva_phy_base",
|
|
"riva_ccu_base", "pronto_a2xb_base", "pronto_ccpu_base",
|
|
"pronto_saw2_base", "wlan_tx_phy_aborts","wlan_brdg_err_source",
|
|
"wlan_tx_status", "alarms_txctl", "alarms_tactl",
|
|
"pronto_mcu_base".
|
|
- interupts: Pronto to Apps interrupts for tx done and rx pending.
|
|
- qcom,pronto-vddmx-supply: regulator to supply pronto pll.
|
|
- qcom,pronto-vddcx-supply: voltage corner regulator to supply WLAN/BT/FM
|
|
digital module.
|
|
- qcom,pronto-vddpx-supply: regulator to supply WLAN DAC.
|
|
- qcom,iris-vddxo-supply : regulator to supply RF XO.
|
|
- qcom,iris-vddrfa-supply : regulator to supply RFA digital.
|
|
- qcom,iris-vddpa-supply : regulator to supply RF PA.
|
|
- qcom,iris-vdddig-supply : regulator to supply RF digital(BT/FM).
|
|
- gpios: gpio numbers to configure 5-wire interface of WLAN connectivity
|
|
- qcom,has-48mhz-xo: boolean flag to determine the usage of 24MHz XO from RF
|
|
- qcom,has-pronto-hw: boolean flag to determine the revId of the WLAN subsystem
|
|
- qcom,wcnss-adc_tm: ADC handle for vbatt notification APIs.
|
|
- qcom,wcnss-vadc: VADC handle for battery voltage notification APIs.
|
|
- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
|
|
- pinctrl-names : Names corresponding to the numbered pinctrl states
|
|
- clocks: from common clock binding: handle to xo and rf_clk clocks.
|
|
- clock-names: Names of all the clocks that are accessed by the subsystem
|
|
- qcom,vdd-voltage-level: This property represents (nominal, min, max) voltage
|
|
for iris and pronto regulators in milli-volts.
|
|
- qcom,vdd-current: This property represents current value for
|
|
iris and pronto regulators in micro-amps.
|
|
|
|
Optional properties:
|
|
- qcom,has-autodetect-xo: boolean flag to determine whether Iris XO auto detect
|
|
should be performed during boot up.
|
|
- qcom,wlan-rx-buff-count: WLAN RX buffer count is a configurable value,
|
|
using a smaller count for this buffer will reduce the memory usage.
|
|
- qcom,is-pronto-v3: boolean flag to determine the pronto hardware version
|
|
in use. subsequently correct workqueue will be used by DXE engine to push frames
|
|
in TX data path.
|
|
- qcom,is-pronto-vadc: boolean flag to determine Battery voltage feature
|
|
support for pronto hardware.
|
|
- qcom,wcnss-pm : <Core rail LDO#, PA rail LDO#, XO settling time,
|
|
RPM power collapse enabled, standalone power collapse enabled>
|
|
Power manager related parameter for LDO configuration.
|
|
11 - WCN CORE rail LDO number
|
|
21 - WCN PA rail LDO number
|
|
1200 - WCN XO settling time (usec)
|
|
1 - WCN RPM power collapse enabled
|
|
1 - WCN standalone power collapse enabled
|
|
6 - GPIO strength value
|
|
- qcom,has-vsys-adc-channel: boolean flag to determine which ADC HW channel need
|
|
to use for VBATT feature.
|
|
|
|
Example:
|
|
|
|
qcom,wcnss-wlan@fb000000 {
|
|
compatible = "qcom,wcnss_wlan";
|
|
reg = <0xfb000000 0x280000>,
|
|
<0xf9011008 0x04>;
|
|
reg-names = "wcnss_mmio", "wcnss_fiq";
|
|
interrupts = <0 145 0 0 146 0>;
|
|
interrupt-names = "wcnss_wlantx_irq", "wcnss_wlanrx_irq";
|
|
|
|
qcom,pronto-vddmx-supply = <&pm8841_s1>;
|
|
qcom,pronto-vddcx-supply = <&pm8841_s2_corner>;
|
|
qcom,pronto-vddpx-supply = <&pm8941_s3>;
|
|
qcom,iris-vddxo-supply = <&pm8941_l6>;
|
|
qcom,iris-vddrfa-supply = <&pm8941_l11>;
|
|
qcom,iris-vddpa-supply = <&pm8941_l19>;
|
|
qcom,iris-vdddig-supply = <&pm8941_l3>;
|
|
|
|
gpios = <&msmgpio 36 0>, <&msmgpio 37 0>, <&msmgpio 38 0>,
|
|
<&msmgpio 39 0>, <&msmgpio 40 0>;
|
|
qcom,has-48mhz-xo;
|
|
qcom,is-pronto-vt;
|
|
qcom,wlan-rx-buff-count = <512>;
|
|
qcom,has-pronto-hw;
|
|
qcom,wcnss-adc_tm = <&pm8226_adc_tm>;
|
|
|
|
pinctrl-names = "wcnss_default", "wcnss_sleep";
|
|
pinctrl-0 = <&wcnss_default>;
|
|
pinctrl-1 = <&wcnss_sleep>;
|
|
pinctrl-2 = <&wcnss_gpio_default>;
|
|
|
|
clocks = <&clock_rpm clk_xo_wlan_clk>,
|
|
<&clock_rpm clk_rf_clk2>,
|
|
<&clock_debug clk_gcc_debug_mux>,
|
|
<&clock_gcc clk_wcnss_m_clk>;
|
|
clock-names = "xo", "rf_clk", "measure", "wcnss_debug";
|
|
qcom,wcnss-pm = <11 21 1200 1 1 6>;
|
|
};
|