107 lines
4.7 KiB
Plaintext
107 lines
4.7 KiB
Plaintext
Qualcomm Serial Peripheral Interface (SPI)
|
|
|
|
Required properties:
|
|
- compatible : Should be "qcom,spi-qup-v2".
|
|
- reg : Offset and length of the register regions for the device
|
|
- reg-names : Register region names referenced in reg above.
|
|
Required register resource entries are:
|
|
"spi_physical" : Physical address of controller register blocks.
|
|
- interrupts : Interrupt numbers used by this controller
|
|
- interrupt-names : Interrupt resource names referenced in interrupts above.
|
|
Required interrupt resource entries are:
|
|
"spi_irq" : QUP-core interrupt.
|
|
- spi-max-frequency : Specifies maximum SPI clock frequency, Units - Hz.
|
|
|
|
Required alias:
|
|
- The desired bus-number is specified via an alias with the following format
|
|
'spi{n}' where n is the bus number.
|
|
|
|
Optional properties:
|
|
- qcom,gpio-mosi : GPIO pin number of the MOSI bus line.
|
|
- qcom,gpio-miso : GPIO pin number of the MISO bus line.
|
|
- qcom,gpio-clk : GPIO pin number of the CLK bus line.
|
|
- qcom,gpio-cs0 : GPIO pin number of the chipselect0 bus line.
|
|
- qcom,gpio-cs1 : GPIO pin number of the chipselect1 bus line.
|
|
- qcom,gpio-cs2 : GPIO pin number of the chipselect2 bus line.
|
|
- qcom,gpio-cs3 : GPIO pin number of the chipselect3 bus line.
|
|
- qcom,infinite-mode: When missing or set to zero, QUP uses infinite-mode. When
|
|
value is non-zero, the value is the number of words in maximum transfer
|
|
length.
|
|
- qcom,active-only : Vote for core clock when the application processor goes
|
|
to active state and remove that vote when it goes to idle state. This flag may
|
|
improve service time of first spi request at the expense of power consumption.
|
|
When this entry is not present, voting is done by the runtime-pm callbacks.
|
|
- qcom,master-id : Master endpoint number used for voting on clocks using the
|
|
bus-scaling driver.
|
|
- qcom,rt-priority : whether spi message queue is set to run as a realtime task.
|
|
With this spi transaction message pump with high (realtime) priority to reduce
|
|
the transfer latency on the bus by minimising the delay between a transfer request
|
|
- qcom,shared : whether this qup is shared with other ee's
|
|
|
|
Optional properties which are required for support of BAM-mode:
|
|
- qcom,ver-reg-exists : Boolean. When present, allows driver to verify if HW
|
|
version support latest features (e.g. BAM) and then enable them. Should be
|
|
removed for legacy HW.
|
|
- qcom,use-bam : Boolean. When present, enables BAM-mode.
|
|
- qcom,use-pinctrl : Boolean. When present, enables pinctrl frame work to configure GPIO's
|
|
instead of existing gpio mux hence gpio entries are no more required if present.
|
|
- pinctrl-names : Property must contain "spi_default" and "spi_sleep" if
|
|
pinctrl is to be used.
|
|
instead of existing gpio mux hence gpio entries are no more required if present.
|
|
- qcom,bam-consumer-pipe-index : BAM consumer-pipe index.
|
|
- qcom,bam-producer-pipe-index : BAM producer-pipe index.
|
|
- reg-names : register region names referenced in reg.
|
|
Required register resource for BAM are:
|
|
"spi_bam_physical" : Physical address of BAM for this controller.
|
|
- interrupt-names : interrupt resource names referenced in interrupts.
|
|
Required interrupt resource from BAM are:
|
|
"spi_bam_irq" : BAM interrupt used by the controller.
|
|
|
|
Optional SPI slave nodes must be children of the SPI master node and contain
|
|
the following properties.
|
|
- reg: (required) chip-select address of the device.
|
|
- compatible : (required) Name of SPI device following generic names.
|
|
- spi-max-frequency : (required) Maximum SPI clocking speed of device in Hz
|
|
- interrupts : (recommended) Should contain the SPI slave interrupt number
|
|
encoded depending on the type of the interrupt controller.
|
|
- interrupt-parent : (recommended) The phandle for the interrupt controller
|
|
that services interrupts for this device.
|
|
- spi-cpol : (optional) Empty property indicating device requires inverse
|
|
clock polarity (CPOL) mode
|
|
- spi-cpha : (optional) Empty property indicating device requires shifted
|
|
clock phase (CPHA) mode
|
|
- spi-cs-high : (optional) Empty property indicating device requires
|
|
chip select active high
|
|
|
|
Example:
|
|
aliases {
|
|
spi0 = &spi_0;
|
|
};
|
|
|
|
spi_0: spi@f9923000 {
|
|
compatible = "qcom,spi-qup-v2";
|
|
|
|
reg-names = "spi_physical", "spi_bam_physical";
|
|
reg = <0xf9923000 0x1000>,
|
|
<0xf9904000 0x10000>;
|
|
interrupt-names = "spi_irq", "spi_bam_irq";
|
|
interrupts = <0 95 0>, <0 238 0>;
|
|
|
|
spi-max-frequency = <19200000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
qcom,gpio-mosi = <&msmgpio 0 0>;
|
|
qcom,gpio-miso = <&msmgpio 1 0>;
|
|
qcom,gpio-clk = <&msmgpio 3 0>;
|
|
qcom,gpio-cs2 = <&msmgpio 9 0>;
|
|
|
|
qcom,infinite-mode = <0>;
|
|
qcom,use-bam;
|
|
qcom,use-pinctrl;
|
|
qcom,bam-consumer-pipe-index = <12>;
|
|
qcom,bam-producer-pipe-index = <13>;
|
|
qcom,ver-reg-exists;
|
|
qcom,master-id = <86>;
|
|
qcom,rt-priority;
|
|
};
|