89 lines
2.8 KiB
Plaintext
89 lines
2.8 KiB
Plaintext
wsa881x Audio CODEC
|
|
|
|
wsa881x Audio CODEC can support either I2C interface or Soundwire interface.
|
|
In Analog mode, this codec will operate as I2C slave device and
|
|
interacts with I2C controller for status, control and interrupt management.
|
|
The wsa881x device nodes will be represented as child nodes to I2C
|
|
master device node in the devicetree. Currently, the below devicetree
|
|
bindings are for I2C mode only and does not include soundwire mode.
|
|
|
|
Required properties:
|
|
|
|
- compatible : "qcom,wsa881x-i2c-codec"
|
|
- reg : Unique device ID of I2C slave device.
|
|
|
|
Optional properties:
|
|
- qcom,msm-gpios : Lists down all the gpio sets that are supported.
|
|
- qcom,pinctrl-names : Lists all the possible combinations of the gpio sets
|
|
mentioned in qcom,msm-gpios. Say we have 2^N combinations for N GPIOs, this
|
|
list all 2^N combinations.
|
|
- pinctrl-names : The combinations of gpio sets from above that are supported in
|
|
the flavor. This can be sometimes same as qcom, pinctrl-names i.e with 2^N
|
|
combinations or will have less incase if some combination is not supported.
|
|
- pinctrl-# : Pinctrl states as mentioned in pinctrl-names.
|
|
|
|
* wsa_intc
|
|
|
|
Required properties:
|
|
|
|
- compatible : "qcom,wsa-irq"
|
|
- interrupt-controller : Mark this device node as an
|
|
interrupt controller
|
|
- #interrupt-cells : Should be 1
|
|
- interrupt-parent : Parent interrupt controller
|
|
- interrupts : Interrupt number on the parent
|
|
interrupt controller
|
|
- interrupt-names : Name of interrupt on the parent
|
|
interrupt controller
|
|
Example:
|
|
|
|
wsa881x-i2c-codec@0e {
|
|
compatible = "qcom,wsa881x-i2c-codec";
|
|
reg = <0x0e>;
|
|
qcom,msm-gpios = "wsa_clk",
|
|
"wsa_reset";
|
|
qcom,pinctrl-names = "all_off",
|
|
"wsa_clk",
|
|
"wsa_active",
|
|
"wsa_clk_active";
|
|
pinctrl-names = "all_off",
|
|
"wsa_clk",
|
|
"wsa_active",
|
|
"wsa_clk_active";
|
|
pinctrl-0 = <&wsa_clk_off &wsa_suspend>;
|
|
pinctrl-1 = <&wsa_clk_on &wsa_suspend>;
|
|
pinctrl-2 = <&wsa_clk_off &wsa_active>;
|
|
pinctrl-3 = <&wsa_clk_on &wsa_active>;
|
|
};
|
|
|
|
wsa881x-i2c-codec@44 {
|
|
compatible = "qcom,wsa881x-i2c-codec";
|
|
reg = <0x44>;
|
|
};
|
|
|
|
wsa881x-i2c-codec@0f {
|
|
compatible = "qcom,wsa881x-i2c-codec";
|
|
reg = <0x0f>;
|
|
qcom,msm-gpios = "wsa_clk",
|
|
"wsa_reset";
|
|
qcom,pinctrl-names = "all_off",
|
|
"wsa_clk",
|
|
"wsa_active",
|
|
"wsa_clk_active";
|
|
pinctrl-names = "all_off",
|
|
"wsa_active",
|
|
"wsa_clk_active";
|
|
pinctrl-0 = <&wsa_clk_off &wsa_suspend>;
|
|
pinctrl-1 = <&wsa_clk_off &wsa_active>;
|
|
pinctrl-2 = <&wsa_clk_on &wsa_active>;
|
|
};
|
|
|
|
wsa_intc: wsa-irq {
|
|
compatible = "qcom,wsa-irq";
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
interrupt-parent = <&msm_gpio>;
|
|
interrupts = <97 0>;
|
|
interrupt-names = "wsa-int";
|
|
};
|