72 lines
3.0 KiB
Plaintext
72 lines
3.0 KiB
Plaintext
Mstar touch controller
|
|
|
|
The mstar controller is connected to host processor
|
|
via i2c. The controller generates interrupts when the
|
|
user touches the panel. The host controller is expected
|
|
to read the touch coordinates over i2c and pass the coordinates
|
|
to the rest of the system.
|
|
|
|
Required properties:
|
|
|
|
- compatible : should be "mstar,msg21xx"
|
|
- reg : i2c slave address of the device
|
|
- interrupt-parent : parent of interrupt
|
|
- interrupts : touch sample interrupt to indicate presense or release
|
|
of fingers on the panel.
|
|
- vdd-supply : Power supply needed to power up the device
|
|
- vcc_i2c-supply : Power source required to power up i2c bus
|
|
- mstar,irq-gpio : irq gpio which is to provide interrupts to host,
|
|
same as "interrupts" node. It will also
|
|
contain active low or active high information.
|
|
- mstar,reset-gpio : reset gpio to control the reset of chip
|
|
- mstar,display-coords : display coords in pixels. It is a four
|
|
tuple consisting of min x, min y, max x and
|
|
max y values
|
|
- pinctrl-names : This should be defined if a target uses pinctrl framework.
|
|
See "pinctrl" in Documentation/devicetree/bindings/pinctrl/msm-pinctrl.txt.
|
|
Specify the names of the configs that pinctrl can install in driver.
|
|
Following are the pinctrl configs that can be installed:
|
|
"pmx_ts_active" : Active configuration of pins, this should specify active
|
|
config defined in pin groups of interrupt and reset gpio.
|
|
"pmx_ts_suspend" : Disabled configuration of pins, this should specify sleep
|
|
config defined in pin groups of interrupt and reset gpio.
|
|
"pmx_ts_release" : Release configuration of pins, this should specify
|
|
release config defined in pin groups of interrupt and reset gpio.
|
|
- mstar,num-max-touches: It defines the maximum number of touch supported by the controller.
|
|
- mstar,hard-reset-delay-ms : hard reset delay in ms
|
|
- mstar,post-hard-reset-delay-ms : post hard reset delay in ms
|
|
|
|
Optional properties:
|
|
|
|
- mstar,button-map : button map of key codes. It is a three tuple consisting of key codes.
|
|
- mstar,panel-coords : panel coords for the chip in pixels.
|
|
It is a four tuple consisting of min x,
|
|
min y, max x and max y values
|
|
- mstar,ic-type : It defines the ic-type of the controller. Values are as folows:
|
|
1 -> msg2133.
|
|
2 -> msg21xxA.
|
|
3 -> msg26xxM.
|
|
|
|
Example:
|
|
i2c@78b9000 { /* BLSP1 QUP5 */
|
|
mstar@26 {
|
|
compatible = "mstar,msg21xx";
|
|
reg = <0x26>;
|
|
interrupt-parent = <&msm_gpio>;
|
|
interrupts = <13 0x2008>;
|
|
mstar,irq-gpio = <&msm_gpio 13 0x00000001>;
|
|
mstar,reset-gpio = <&msm_gpio 12 0x0>;
|
|
vdd-supply = <&pm8916_l17>;
|
|
vcc_i2c-supply = <&pm8916_l6>;
|
|
mstar,display-coords = <0 0 480 854>;
|
|
pinctrl-names = "pmx_ts_active","pmx_ts_suspend";
|
|
pinctrl-0 = <&ts_int_active &ts_reset_active>;
|
|
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
|
mstar,button-map = <172 139 158>;
|
|
mstar,ic-type = <2>;
|
|
mstar,num_max_touches = <2>;
|
|
mstar,hard-reset-delay-ms = <100>;
|
|
mstar,post-hard-reset-delay-ms = <100>;
|
|
};
|
|
};
|