M7350/kernel/arch/arm/boot/dts/qcom/dsi-panel-sim-dualmipi-cmd.dtsi
2024-09-09 08:57:42 +00:00

93 lines
3.3 KiB
Plaintext

/* Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
&mdss_mdp {
dsi_dual_sim_cmd: qcom,mdss_dsi_dual_sim_cmd {
qcom,mdss-dsi-panel-name = "Sim dual cmd mode dsi panel";
qcom,mdss-dsi-panel-type = "dsi_cmd_mode";
qcom,mdss-dsi-panel-framerate = <60>;
qcom,mdss-dsi-virtual-channel-id = <0>;
qcom,mdss-dsi-stream = <0>;
qcom,mdss-dsi-panel-width = <1280>;
qcom,mdss-dsi-panel-height = <1440>;
qcom,mdss-dsi-h-front-porch = <120>;
qcom,mdss-dsi-h-back-porch = <44>;
qcom,mdss-dsi-h-pulse-width = <16>;
qcom,mdss-dsi-h-sync-skew = <0>;
qcom,mdss-dsi-v-back-porch = <4>;
qcom,mdss-dsi-v-front-porch = <8>;
qcom,mdss-dsi-v-pulse-width = <4>;
qcom,mdss-dsi-h-left-border = <0>;
qcom,mdss-dsi-h-right-border = <0>;
qcom,mdss-dsi-v-top-border = <0>;
qcom,mdss-dsi-v-bottom-border = <0>;
qcom,mdss-dsi-bpp = <24>;
qcom,mdss-dsi-color-order = "rgb_swap_rgb";
qcom,mdss-dsi-underflow-color = <0xff>;
qcom,mdss-dsi-border-color = <0>;
qcom,mdss-dsi-h-sync-pulse = <0>;
qcom,mdss-dsi-traffic-mode = "non_burst_sync_event";
qcom,mdss-dsi-bllp-eof-power-mode;
qcom,mdss-dsi-bllp-power-mode;
qcom,cmd-sync-wait-broadcast;
qcom,mdss-dsi-lane-0-state;
qcom,mdss-dsi-lane-1-state;
qcom,mdss-dsi-lane-2-state;
qcom,mdss-dsi-lane-3-state;
qcom,mdss-dsi-hor-line-idle = <0 40 256>,
<40 120 128>,
<120 240 64>;
qcom,mdss-dsi-panel-timings = [cd 32 22 00 60 64 26 34 29 03
04 00];
qcom,mdss-dsi-reset-sequence = <1 10>, <0 10>, <1 10>;
qcom,mdss-dsi-t-clk-post = <0x03>;
qcom,mdss-dsi-t-clk-pre = <0x27>;
qcom,mdss-dsi-bl-max-level = <4095>;
qcom,mdss-dsi-dma-trigger = "trigger_sw";
qcom,mdss-dsi-mdp-trigger = "none";
qcom,mdss-dsi-te-pin-select = <1>;
qcom,mdss-dsi-wr-mem-start = <0x2c>;
qcom,mdss-dsi-wr-mem-continue = <0x3c>;
qcom,mdss-dsi-te-dcs-command = <1>;
qcom,mdss-dsi-te-check-enable;
qcom,mdss-dsi-te-using-te-pin;
qcom,mdss-dsi-on-command = [29 01 00 00 00 00 02 b0 03
05 01 00 00 0a 00 01 00
/* Soft reset, wait 10ms */
15 01 00 00 0a 00 02 3a 77
/* Set Pixel format (24 bpp) */
39 01 00 00 0a 00 05 2a 00 00 04 ff
/* Set Column address */
39 01 00 00 0a 00 05 2b 00 00 05 9f
/* Set page address */
15 01 00 00 0a 00 02 35 00
/* Set tear on */
39 01 00 00 0a 00 03 44 00 00
/* Set tear scan line */
15 01 00 00 0a 00 02 51 ff
/* write display brightness */
15 01 00 00 0a 00 02 53 24
/* write control brightness */
15 01 00 00 0a 00 02 55 00
/* CABC brightness */
05 01 00 00 78 00 01 11
/* exit sleep mode, wait 120ms */
05 01 00 00 10 00 01 29];
/* Set display on, wait 16ms */
qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
qcom,mdss-dsi-off-command = [05 01 00 00 32 00 02 28 00
05 01 00 00 78 00 02 10 00];
qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
qcom,panel-ack-disabled;
};
};