M7350/kernel/include/linux/regulator/qpnp-regulator.h
2024-09-09 08:52:07 +00:00

198 lines
7.4 KiB
C

/*
* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef __REGULATOR_QPNP_REGULATOR_H__
#define __REGULATOR_QPNP_REGULATOR_H__
#include <linux/regulator/machine.h>
#define QPNP_REGULATOR_DRIVER_NAME "qcom,qpnp-regulator"
/* Pin control enable input pins. */
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_NONE 0x00
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN0 0x01
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN1 0x02
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN2 0x04
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_EN3 0x08
#define QPNP_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT 0x10
/* Pin control high power mode input pins. */
#define QPNP_REGULATOR_PIN_CTRL_HPM_NONE 0x00
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN0 0x01
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN1 0x02
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN2 0x04
#define QPNP_REGULATOR_PIN_CTRL_HPM_EN3 0x08
#define QPNP_REGULATOR_PIN_CTRL_HPM_SLEEP_B 0x10
#define QPNP_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT 0x20
/*
* Used with enable parameters to specify that hardware default register values
* should be left unaltered.
*/
#define QPNP_REGULATOR_DISABLE 0
#define QPNP_REGULATOR_ENABLE 1
#define QPNP_REGULATOR_USE_HW_DEFAULT 2
/* Soft start strength of a voltage switch type regulator */
enum qpnp_vs_soft_start_str {
QPNP_VS_SOFT_START_STR_0P05_UA,
QPNP_VS_SOFT_START_STR_0P25_UA,
QPNP_VS_SOFT_START_STR_0P55_UA,
QPNP_VS_SOFT_START_STR_0P75_UA,
QPNP_VS_SOFT_START_STR_HW_DEFAULT,
};
/* Current limit of a boost type regulator */
enum qpnp_boost_current_limit {
QPNP_BOOST_CURRENT_LIMIT_300_MA,
QPNP_BOOST_CURRENT_LIMIT_600_MA,
QPNP_BOOST_CURRENT_LIMIT_900_MA,
QPNP_BOOST_CURRENT_LIMIT_1200_MA,
QPNP_BOOST_CURRENT_LIMIT_1500_MA,
QPNP_BOOST_CURRENT_LIMIT_1800_MA,
QPNP_BOOST_CURRENT_LIMIT_2100_MA,
QPNP_BOOST_CURRENT_LIMIT_2400_MA,
QPNP_BOOST_CURRENT_LIMIT_HW_DEFAULT,
};
/**
* struct qpnp_regulator_platform_data - qpnp-regulator initialization data
* @init_data: regulator constraints
* @pull_down_enable: 1 = Enable output pull down resistor when the
* regulator is disabled
* 0 = Disable pull down resistor
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
* pull down state
* @pin_ctrl_enable: Bit mask specifying which hardware pins should be
* used to enable the regulator, if any
* Value should be an ORing of
* QPNP_REGULATOR_PIN_CTRL_ENABLE_* constants. If
* the bit specified by
* QPNP_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT is
* set, then pin control enable hardware registers
* will not be modified.
* @pin_ctrl_hpm: Bit mask specifying which hardware pins should be
* used to force the regulator into high power
* mode, if any
* Value should be an ORing of
* QPNP_REGULATOR_PIN_CTRL_HPM_* constants. If
* the bit specified by
* QPNP_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT is
* set, then pin control mode hardware registers
* will not be modified.
* @system_load: Load in uA present on regulator that is not captured
* by any consumer request
* @enable_time: Time in us to delay after enabling the regulator
* @ocp_enable: 1 = Allow over current protection (OCP) to be
* enabled for voltage switch type regulators so
* that they latch off automatically when over
* current is detected. OCP is enabled when in HPM
* or auto mode.
* 0 = Disable OCP
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
* OCP state
* @ocp_irq: IRQ number of the voltage switch OCP IRQ. If
* specified the voltage switch will be toggled off
* and back on when OCP triggers in order to handle
* high in-rush current.
* @ocp_max_retries: Maximum number of times to try toggling a voltage
* switch off and back on as a result of
* consecutive over current events.
* @ocp_retry_delay_ms: Time to delay in milliseconds between each
* voltage switch toggle after an over current
* event takes place.
* @boost_current_limit: This parameter sets the current limit of boost type
* regulators. Its value should be one of
* QPNP_BOOST_CURRENT_LIMIT_*. If its value is
* QPNP_BOOST_CURRENT_LIMIT_HW_DEFAULT, then the
* boost current limit will be left at its default
* hardware value.
* @soft_start_enable: 1 = Enable soft start for LDO and voltage switch
* type regulators so that output voltage slowly
* ramps up when the regulator is enabled
* 0 = Disable soft start
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
* soft start state
* @vs_soft_start_strength: This parameter sets the soft start strength for
* voltage switch type regulators. Its value
* should be one of QPNP_VS_SOFT_START_STR_*. If
* its value is QPNP_VS_SOFT_START_STR_HW_DEFAULT,
* then the soft start strength will be left at its
* default hardware value.
* @auto_mode_enable: 1 = Enable automatic hardware selection of regulator
* mode (HPM vs LPM). Auto mode is not available
* on boost type regulators
* 0 = Disable auto mode selection
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
* auto mode state
* @bypass_mode_enable: 1 = Enable bypass mode for an LDO type regulator so
* that it acts like a switch and simply outputs
* its input voltage
* 0 = Do not enable bypass mode
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
* bypass mode state
* @hpm_enable: 1 = Enable high power mode (HPM), also referred to
* as NPM. HPM consumes more ground current than
* LPM, but it can source significantly higher load
* current. HPM is not available on boost type
* regulators. For voltage switch type regulators,
* HPM implies that over current protection and
* soft start are active all the time. This
* configuration can be overwritten by changing the
* regulator's mode dynamically.
* 0 = Do not enable HPM
* QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
* HPM state
* @base_addr: SMPI base address for the regulator peripheral
*/
struct qpnp_regulator_platform_data {
struct regulator_init_data init_data;
int pull_down_enable;
unsigned pin_ctrl_enable;
unsigned pin_ctrl_hpm;
int system_load;
int enable_time;
int ocp_enable;
int ocp_irq;
int ocp_max_retries;
int ocp_retry_delay_ms;
enum qpnp_boost_current_limit boost_current_limit;
int soft_start_enable;
enum qpnp_vs_soft_start_str vs_soft_start_strength;
int auto_mode_enable;
int bypass_mode_enable;
int hpm_enable;
u16 base_addr;
};
#ifdef CONFIG_REGULATOR_QPNP
/**
* qpnp_regulator_init() - register spmi driver for qpnp-regulator
*
* This initialization function should be called in systems in which driver
* registration ordering must be controlled precisely.
*/
int __init qpnp_regulator_init(void);
#else
static inline int __init qpnp_regulator_init(void)
{
return -ENODEV;
}
#endif /* CONFIG_REGULATOR_QPNP */
#endif