223 lines
7.9 KiB
Plaintext
223 lines
7.9 KiB
Plaintext
Qualcomm GPU
|
|
|
|
Qualcomm Adreno GPU
|
|
|
|
Required properties:
|
|
- label: A string used as a descriptive name for the device.
|
|
- compatible: Must be "qcom,kgsl-3d0" and "qcom,kgsl-3d"
|
|
- reg: Specifies the register base address and size. The second interval
|
|
specifies the shader memory base address and size.
|
|
- reg-names: Resource names used for the physical address of device registers
|
|
and shader memory. "kgsl_3d0_reg_memory" gives the physical address
|
|
and length of device registers while "kgsl_3d0_shader_memory" gives
|
|
physical address and length of device shader memory. If
|
|
specified, "qfprom_memory" gives the range for the efuse
|
|
registers used for various configuration options.
|
|
- interrupts: Interrupt mapping for GPU IRQ.
|
|
- interrupt-names: String property to describe the name of the interrupt.
|
|
- qcom,id: An integer used as an identification number for the device.
|
|
|
|
- clocks: List of phandle and clock specifier pairs, one pair
|
|
for each clock input to the device.
|
|
- clock-names: List of clock input name strings sorted in the same
|
|
order as the clocks property.
|
|
Current values of clock-names are:
|
|
"src_clk", "core_clk", "iface_clk", "mem_clk", "mem_iface_clk",
|
|
"alt_mem_iface_clk", "rbbmtimer_clk", "alwayson_clk"
|
|
"core_clk" and "iface_clk" are required and others are optional
|
|
|
|
- qcom,base-leakage-coefficient: Dynamic leakage coefficient.
|
|
- qcom,lm-limit: Current limit for GPU limit management.
|
|
|
|
Bus Scaling Data:
|
|
- qcom,msm-bus,name: String property to describe the name of the 3D graphics processor.
|
|
- qcom,msm-bus,num-cases: This is the the number of Bus Scaling use cases defined in the vectors property.
|
|
- qcom,msm-bus,active-only: A boolean flag indicating if it is active only.
|
|
- qcom,msm-bus,num-paths: This represents the number of paths in each Bus Scaling Usecase.
|
|
- qcom,msm-bus,vectors-KBps: A series of 4 cell properties, format of which is:
|
|
<src dst ab ib>, <src dst ab ib>, // For Bus Scaling Usecase 1
|
|
<src dst ab ib>, <src dst ab ib>, // For Bus Scaling Usecase 2
|
|
<.. .. .. ..>, <.. .. .. ..>; // For Bus Scaling Usecase n
|
|
This property is a series of all vectors for all Bus Scaling Usecases.
|
|
Each set of vectors for each usecase describes bandwidth votes for a combination
|
|
of src/dst ports. The driver will set the desired use case based on the selected
|
|
power level and the desired bandwidth vote will be registered for the port pairs.
|
|
Current values of src are:
|
|
0 = MSM_BUS_MASTER_GRAPHICS_3D
|
|
1 = MSM_BUS_MASTER_GRAPHICS_3D_PORT1
|
|
2 = MSM_BUS_MASTER_V_OCMEM_GFX3D
|
|
Current values of dst are:
|
|
0 = MSM_BUS_SLAVE_EBI_CH0
|
|
1 = MSM_BUS_SLAVE_OCMEM
|
|
ab: Represents aggregated bandwidth. This value is 0 for Graphics.
|
|
ib: Represents instantaneous bandwidth. This value has a range <0 8000 MB/s>
|
|
|
|
- qcom,ocmem-bus-client: Container for another set of bus scaling properties
|
|
qcom,msm-bus,name
|
|
qcom,msm-bus,num-cases
|
|
qcom,msm-bus,num-paths
|
|
qcom,msm-bus,vectors-KBps
|
|
to be used by ocmem msm bus scaling client.
|
|
|
|
GDSC Oxili Regulators:
|
|
- regulator-names: List of regulator name strings sorted in power-on order
|
|
- vddcx-supply: Phandle for vddcx regulator device node.
|
|
- vdd-supply: Phandle for vdd regulator device node.
|
|
|
|
IOMMU Data:
|
|
- iommu: Phandle for the KGSL IOMMU device node
|
|
|
|
GPU Power levels:
|
|
- qcom,gpu-pwrlevel-bins: Container for sets of GPU power levels (see
|
|
adreno-pwrlevels.txt)
|
|
|
|
DCVS Core info
|
|
- qcom,dcvs-core-info Container for the DCVS core info (see
|
|
dcvs-core-info.txt)
|
|
|
|
Optional Properties:
|
|
- qcom,initial-powerlevel: This value indicates which qcom,gpu-pwrlevel should be used at start time
|
|
and when coming back out of resume
|
|
- qcom,bus-control: Boolean. Enables an independent bus vote from the gpu frequency
|
|
- qcom,bus-width: Bus width in number of bytes. This enables dynamic AB bus voting based on
|
|
bus width and actual bus transactions.
|
|
- qcom,gpubw-dev: a phandle to a device representing bus bandwidth requirements
|
|
(see devdw.txt)
|
|
- qcom,idle-timeout: This property represents the time in milliseconds for idle timeout.
|
|
- qcom,deep-nap-timeout: This property represents the time in milliseconds for entering deeper
|
|
power state.
|
|
- qcom,chipid: If it exists this property is used to replace
|
|
the chip identification read from the GPU hardware.
|
|
This is used to override faulty hardware readings.
|
|
- qcom,strtstp-sleepwake: Boolean. Enables use of GPU SLUMBER instead of SLEEP for power savings
|
|
- qcom,gx-retention: Boolean. Enables use of GX rail RETENTION voltage
|
|
|
|
- qcom,pm-qos-active-latency:
|
|
Right after GPU wakes up from sleep, driver votes for
|
|
acceptable maximum latency to the pm-qos driver. This
|
|
voting demands that the system can not go into any
|
|
power save state *if* the latency to bring system back
|
|
into active state is more than this value.
|
|
Value is in microseconds.
|
|
- qcom,pm-qos-wakeup-latency:
|
|
Similar to the above. Driver votes against deep low
|
|
power modes right before GPU wakes up from sleep.
|
|
- qcom,force-32bit:
|
|
Force the GPU to use 32 bit data sizes even if
|
|
it is capable of doing 64 bit.
|
|
|
|
- qcom,gpu-quirk-two-pass-use-wfi:
|
|
Signal the GPU to set Set TWOPASSUSEWFI bit in
|
|
A5XX_PC_DBG_ECO_CNTL (5XX only)
|
|
|
|
The following properties are optional as collecting data via coresight might
|
|
not be supported for every chipset. The documentation for coresight
|
|
properties can be found in:
|
|
Documentation/devicetree/bindings/coresight/coresight.txt
|
|
|
|
- coresight-id Unique integer identifier for the bus.
|
|
- coresight-name Unique descriptive name of the bus.
|
|
- coresight-nr-inports Number of input ports on the bus.
|
|
- coresight-outports List of output port numbers on the bus.
|
|
- coresight-child-list List of phandles pointing to the children of this
|
|
component.
|
|
- coresight-child-ports List of input port numbers of the children.
|
|
|
|
|
|
Example of A330 GPU in MSM8916:
|
|
|
|
&soc {
|
|
msm_gpu: qcom,kgsl-3d0@01c00000 {
|
|
label = "kgsl-3d0";
|
|
compatible = "qcom,kgsl-3d0", "qcom,kgsl-3d";
|
|
reg = <0x01c00000 0x10000
|
|
0x01c20000 0x20000>;
|
|
reg-names = "kgsl_3d0_reg_memory" , "kgsl_3d0_shader_memory";
|
|
interrupts = <0 33 0>;
|
|
interrupt-names = "kgsl_3d0_irq";
|
|
qcom,id = <0>;
|
|
|
|
qcom,chipid = <0x03000600>;
|
|
|
|
qcom,initial-pwrlevel = <1>;
|
|
|
|
/* Idle Timeout = HZ/12 */
|
|
qcom,idle-timeout = <8>;
|
|
qcom,strtstp-sleepwake;
|
|
|
|
clocks = <&clock_gcc clk_gcc_oxili_gfx3d_clk>,
|
|
<&clock_gcc clk_gcc_oxili_ahb_clk>,
|
|
<&clock_gcc clk_gcc_oxili_gmem_clk>,
|
|
<&clock_gcc clk_gcc_bimc_gfx_clk>,
|
|
<&clock_gcc clk_gcc_bimc_gpu_clk>;
|
|
clock-names = "core_clk", "iface_clk", "mem_clk",
|
|
"mem_iface_clk", "alt_mem_iface_clk";
|
|
|
|
/* Bus Scale Settings */
|
|
qcom,msm-bus,name = "grp3d";
|
|
qcom,msm-bus,num-cases = <4>;
|
|
qcom,msm-bus,num-paths = <1>;
|
|
qcom,msm-bus,vectors-KBps =
|
|
<26 512 0 0>,
|
|
<26 512 0 1600000>,
|
|
<26 512 0 3200000>,
|
|
<26 512 0 4264000>;
|
|
|
|
/* GDSC oxili regulators */
|
|
vdd-supply = <&gdsc_oxili_gx>;
|
|
|
|
/* IOMMU Data */
|
|
iommu = <&gfx_iommu>;
|
|
|
|
/* Trace bus */
|
|
coresight-id = <67>;
|
|
coresight-name = "coresight-gfx";
|
|
coresight-nr-inports = <0>;
|
|
coresight-outports = <0>;
|
|
coresight-child-list = <&funnel_in0>;
|
|
coresight-child-ports = <5>;
|
|
|
|
/* Power levels */
|
|
qcom,gpu-pwrlevels-bins {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
qcom,gpu-pwrlevels-0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
qcom,speed-bin = <0>;
|
|
|
|
qcom,gpu-pwrlevel@0 {
|
|
reg = <0>;
|
|
qcom,gpu-freq = <400000000>;
|
|
qcom,bus-freq = <3>;
|
|
qcom,io-fraction = <33>;
|
|
};
|
|
|
|
qcom,gpu-pwrlevel@1 {
|
|
reg = <1>;
|
|
qcom,gpu-freq = <310000000>;
|
|
qcom,bus-freq = <2>;
|
|
qcom,io-fraction = <66>;
|
|
};
|
|
|
|
qcom,gpu-pwrlevel@2 {
|
|
reg = <2>;
|
|
qcom,gpu-freq = <200000000>;
|
|
qcom,bus-freq = <1>;
|
|
qcom,io-fraction = <100>;
|
|
};
|
|
|
|
qcom,gpu-pwrlevel@3 {
|
|
reg = <3>;
|
|
qcom,gpu-freq = <27000000>;
|
|
qcom,bus-freq = <0>;
|
|
qcom,io-fraction = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
};
|
|
};
|