MSM SuperSpeed USB3.0 SoC controller

Required properties :
- compatible : should be "qcom,dwc-usb3-msm"
 - reg: Address and length of the register set for the device
   Required regs are:
	"core_base" : usb controller register set
- interrupts: IRQ lines used by this controller
- interrupt-names : Interrupt resource entries are :
	"hs_phy_irq" : Interrupt from HS PHY for asynchronous events in LPM.
	"pwr_event_irq" : Interrupt to controller for asynchronous events in LPM.
	Used for SS-USB power events.

Optional properties :
- reg: Additional registers
     "tcsr_base" : top-level CSR register to be written during power-on reset
     initialize the internal MUX that controls whether to use USB3 controller
     with primary port.
     "ahb2phy_base" : top-level register to configure read/write wait cycle with
     both QMP and QUSB PHY registers.
- Refer to "Documentation/devicetree/bindings/arm/msm/msm_bus.txt" for
  below optional properties:
    - qcom,msm_bus,name
    - qcom,msm_bus,num_cases
    - qcom,msm_bus,num_paths
    - qcom,msm_bus,vectors
- interrupt-names : Optional interrupt resource entries are:
    "pmic_id_irq" : Interrupt from PMIC for external ID pin notification.
    "ss_phy_irq"  : Interrupt from super speed phy for wake up notification.
- qcom,charging-disabled: If present then battery charging using USB
  is disabled.
- vbus_dwc3-supply: phandle to the 5V VBUS supply regulator used for host mode.
- USB3_GDSC-supply : phandle to the globally distributed switch controller
  regulator node to the USB controller.
- qcom,dwc-usb3-msm-tx-fifo-size: If present, represents RAM size available for
		TX fifo allocation in bytes
- qcom,usb-dbm : phandle for the DBM device
- qcom,lpm-to-suspend-delay-ms: Indicates timeout (in milliseconds) to release wakeup source
  after USB is kept into LPM.
- qcom,ext-hub-reset-gpio: This corresponds to gpio which is used for HUB reset.
- qcom,disable-dev-mode-pm: If present, it disables PM runtime functionality for device mode.
- qcom,disable-host-mode-pm: If present, it disables XHCI PM runtime functionality when USB
  host mode is used.
Sub nodes:
- Sub node for "DWC3- USB3 controller".
  This sub node is required property for device node. The properties of this subnode
  are specified in dwc3.txt.

Example MSM USB3.0 controller device node :
	usb@f9200000 {
		compatible = "qcom,dwc-usb3-msm";
		reg = <0xf9200000 0xfc000>,
		      <0xfd4ab000 0x4>,
		      <0xf9b3e000 0x3ff>;
		reg-names = "core_base",
			"tcsr_base",
			"ahb2phy_base",
		interrupts = <0 133 0>;
		interrupt-names = "hs_phy_irq";
		vbus_dwc3-supply = <&pm8941_mvs1>;
		USB3_GDSC-supply = <&gdsc_usb30>;
		qcom,dwc-usb3-msm-dbm-eps = <4>
		qcom,dwc_usb3-adc_tm = <&pm8941_adc_tm>;
		qcom,dwc-usb3-msm-tx-fifo-size = <29696>;
		qcom,usb-dbm = <&dbm_1p4>;
		qcom,lpm-to-suspend-delay-ms = <2>;

		qcom,msm_bus,name = "usb3";
		qcom,msm_bus,num_cases = <2>;
		qcom,msm_bus,num_paths = <1>;
		qcom,msm_bus,vectors =
				<61 512 0 0>,
				<61 512 240000000 960000000>;
		dwc3@f9200000 {
			compatible = "synopsys,dwc3";
			reg = <0xf9200000 0xfc000>;
			interrupts = <0 131 0>, <0 179 0>;
			interrupt-names = "irq", "otg_irq";
			tx-fifo-resize;
		};
	};