Qualcomm mdss-dsi-panel mdss-dsi-panel is a dsi panel device which supports panels that are compatable with MIPI display serial interface specification. Required properties: - compatible: This property applies to DSI V2 panels only. This property should not be added for panels that work based on version "V6.0" DSI panels that are of different versions are initialized by the drivers for dsi controller. This property specifies the version for DSI HW that this panel will work with "qcom,dsi-panel-v2" = DSI V2.0 - status: This property applies to DSI V2 panels only. This property should not be added for panels that work based on version "V6.0" DSI panels that are of different versions are initialized by the drivers for dsi controller. A string that has to be set to "okay/ok" to enable the panel driver. By default this property will be set to "disable". Will be set to "ok/okay" status for specific platforms. - qcom,mdss-dsi-panel-controller: Specifies the phandle for the DSI controller that this panel will be mapped to. - qcom,mdss-dsi-panel-width: Specifies panel width in pixels. - qcom,mdss-dsi-panel-height: Specifies panel height in pixels. - qcom,mdss-dsi-bpp: Specifies the panel bits per pixel. 3 = for rgb111 8 = for rgb332 12 = for rgb444 16 = for rgb565 18 = for rgb666 24 = for rgb888 - qcom,mdss-dsi-panel-destination: A string that specifies the destination display for the panel. "display_1" = DISPLAY_1 "display_2" = DISPLAY_2 - qcom,mdss-dsi-panel-timings: An array of length 12 that specifies the PHY timing settings for the panel. - qcom,mdss-dsi-panel-timings-8996: An array of length 40 char that specifies the 8996 PHY lane timing settings for the panel. - qcom,mdss-dsi-on-command: A byte stream formed by multiple dcs packets base on qcom dsi controller protocol. byte 0: dcs data type byte 1: set to indicate this is an individual packet (no chain) byte 2: virtual channel number byte 3: expect ack from client (dcs read command) byte 4: wait number of specified ms after dcs command transmitted byte 5, 6: 16 bits length in network byte order byte 7 and beyond: number byte of payload - qcom,mdss-dsi-off-command: A byte stream formed by multiple dcs packets base on qcom dsi controller protocol. byte 0: dcs data type byte 1: set to indicate this is an individual packet (no chain) byte 2: virtual channel number byte 3: expect ack from client (dcs read command) byte 4: wait number of specified ms after dcs command transmitted byte 5, 6: 16 bits length in network byte order byte 7 and beyond: number byte of payload - qcom,mdss-dsi-post-panel-on-command: same as "qcom,mdss-dsi-on-command" except commands are sent after displaying an image. Note, if a short DCS packet(i.e packet with Byte 0:dcs data type as 05) mentioned in qcom,mdss-dsi-on-command/qcom,mdss-dsi-off-command stream fails to transmit, then 3 options can be tried. 1. Send the packet as a long packet instead Byte 0: dcs data type = 05 (DCS short Packet) Byte 0: dcs data type = 29 (DCS long Packet) 2. Send the packet in one burst by prepending with the next packet in packet stream Byte 1 = 01 (indicates this is an individual packet) Byte 1 = 00 (indicates this will be appended to the next individual packet in the packet stream) 3. Prepend a NULL packet to the short packet and send both in one burst instead of combining multiple short packets and sending them in one burst. Optional properties: - qcom,mdss-dsi-panel-name: A string used as a descriptive name of the panel - qcom,cmd-sync-wait-broadcast: Boolean used to broadcast dcs command to panels. - qcom,mdss-dsi-fbc-enable: Boolean used to enable frame buffer compression mode. - qcom,mdss-dsi-fbc-slice-height: Slice height(in lines) of compressed block. Expressed as power of 2. To set as 128 lines, this should be set to 7. - qcom,mdss-dsi-fbc-2d-pred-mode: Boolean to enable 2D map prediction. - qcom,mdss-dsi-fbc-ver2-mode: Boolean to enable FBC 2.0 that supports 1/3 compression. - qcom,mdss-dsi-fbc-bpp: Compressed bpp supported by the panel. Specified color order is used as default value. - qcom,mdss-dsi-fbc-packing: Component packing. 0 = default value. - qcom,mdss-dsi-fbc-quant-error: Boolean used to enable quantization error calculation. - qcom,mdss-dsi-fbc-bias: Bias for CD. 0 = default value. - qcom,mdss-dsi-fbc-pat-mode: Boolean used to enable PAT mode. - qcom,mdss-dsi-fbc-vlc-mode: Boolean used to enable VLC mode. - qcom,mdss-dsi-fbc-bflc-mode: Boolean used to enable BFLC mode. - qcom,mdss-dsi-fbc-h-line-budget: Per line extra budget. 0 = default value. - qcom,mdss-dsi-fbc-budget-ctrl: Extra budget level. 0 = default value. - qcom,mdss-dsi-fbc-block-budget: Per block budget. 0 = default value. - qcom,mdss-dsi-fbc-lossless-threshold: Lossless mode threshold. 0 = default value. - qcom,mdss-dsi-fbc-lossy-threshold: Lossy mode threshold. 0 = default value. - qcom,mdss-dsi-fbc-rgb-threshold: Lossy RGB threshold. 0 = default value. - qcom,mdss-dsi-fbc-lossy-mode-idx: Lossy mode index value. 0 = default value. - qcom,mdss-dsi-fbc-max-pred-err: Max quantization prediction error. 0 = default value - qcom,mdss-dsi-h-back-porch: Horizontal back porch value in pixel. 6 = default value. - qcom,mdss-dsi-h-front-porch: Horizontal front porch value in pixel. 6 = default value. - qcom,mdss-dsi-h-pulse-width: Horizontal pulse width. 2 = default value. - qcom,mdss-dsi-h-sync-skew: Horizontal sync skew value. 0 = default value. - qcom,mdss-dsi-v-back-porch: Vertical back porch value in pixel. 6 = default value. - qcom,mdss-dsi-v-front-porch: Vertical front porch value in pixel. 6 = default value. - qcom,mdss-dsi-v-pulse-width: Vertical pulse width. 2 = default value. - qcom,mdss-dsi-h-left-border: Horizontal left border in pixel. 0 = default value - qcom,mdss-dsi-h-right-border: Horizontal right border in pixel. 0 = default value - qcom,mdss-dsi-v-top-border: Vertical top border in pixel. 0 = default value - qcom,mdss-dsi-v-bottom-border: Vertical bottom border in pixel. 0 = default value - qcom,mdss-dsi-underflow-color: Specifies the controller settings for the panel under flow color. 0xff = default value. - qcom,mdss-dsi-border-color: Defines the border color value if border is present. 0 = default value. - qcom,mdss-dsi-pan-enable-dynamic-fps: Boolean used to enable change in frame rate dynamically. - qcom,mdss-dsi-pan-fps-update: A string that specifies when to change the frame rate. "dfps_suspend_resume_mode"= FPS change request is implemented during suspend/resume. "dfps_immediate_clk_mode" = FPS change request is implemented immediately using DSI clocks. "dfps_immediate_porch_mode_hfp" = FPS change request is implemented immediately by changing panel horizontal front porch values. "dfps_immediate_porch_mode_vfp" = FPS change request is implemented immediately by changing panel vertical front porch values. - qcom,min-refresh-rate: Minimum refresh rate supported by the panel. - qcom,max-refresh-rate: Maximum refresh rate supported by the panel. If max refresh rate is not specified, then the frame rate of the panel in qcom,mdss-dsi-panel-framerate is used. - qcom,mdss-dsi-bl-pmic-control-type: A string that specifies the implementation of backlight control for this panel. "bl_ctrl_pwm" = Backlight controlled by PWM gpio. "bl_ctrl_wled" = Backlight controlled by WLED. "bl_ctrl_dcs" = Backlight controlled by DCS commands. other: Unknown backlight control. (default) - qcom,mdss-dsi-bl-pwm-pmi: Boolean to indicate that PWM control is through second pmic chip. - qcom,mdss-dsi-bl-pmic-bank-select: LPG channel for backlight. Requred if blpmiccontroltype is PWM - qcom,mdss-dsi-bl-pmic-pwm-frequency: PWM period in microseconds. Requred if blpmiccontroltype is PWM - qcom,mdss-dsi-pwm-gpio: PMIC gpio binding to backlight. Requred if blpmiccontroltype is PWM - qcom,mdss-dsi-bl-min-level: Specifies the min backlight level supported by the panel. 0 = default value. - qcom,mdss-dsi-bl-max-level: Specifies the max backlight level supported by the panel. 255 = default value. - qcom,mdss-brightness-max-level: Specifies the max brightness level supported. 255 = default value. - qcom,mdss-dsi-interleave-mode: Specifies interleave mode. 0 = default value. - qcom,mdss-dsi-panel-type: Specifies the panel operating mode. "dsi_video_mode" = enable video mode (default). "dsi_cmd_mode" = enable command mode. - qcom,5v-boost-gpio: Specifies the panel gpio for display 5v boost. - qcom,mdss-dsi-te-check-enable: Boolean to enable Tear Check configuration. - qcom,mdss-dsi-te-using-te-pin: Boolean to specify whether using hardware vsync. - qcom,mdss-dsi-te-pin-select: Specifies TE operating mode. 0 = TE through embedded dcs command 1 = TE through TE gpio pin. (default) - qcom,mdss-dsi-te-dcs-command: Inserts the dcs command. 1 = default value. - qcom,mdss-dsi-wr-mem-start: DCS command for write_memory_start. 0x2c = default value. - qcom,mdss-dsi-wr-mem-continue: DCS command for write_memory_continue. 0x3c = default value. - qcom,mdss-dsi-h-sync-pulse: Specifies the pulse mode option for the panel. 0 = Don't send hsa/he following vs/ve packet(default) 1 = Send hsa/he following vs/ve packet - qcom,mdss-dsi-hfp-power-mode: Boolean to determine DSI lane state during horizontal front porch (HFP) blanking period. - qcom,mdss-dsi-hbp-power-mode: Boolean to determine DSI lane state during horizontal back porch (HBP) blanking period. - qcom,mdss-dsi-hsa-power-mode: Boolean to determine DSI lane state during horizontal sync active (HSA) mode. - qcom,mdss-dsi-last-line-interleave Boolean to determine if last line interleave flag needs to be enabled. - qcom,mdss-dsi-bllp-eof-power-mode: Boolean to determine DSI lane state during blanking low power period (BLLP) EOF mode. - qcom,mdss-dsi-bllp-power-mode: Boolean to determine DSI lane state during blanking low power period (BLLP) mode. - qcom,mdss-dsi-traffic-mode: Specifies the panel traffic mode. "non_burst_sync_pulse" = non burst with sync pulses (default). "non_burst_sync_event" = non burst with sync start event. "burst_mode" = burst mode. - qcom,mdss-dsi-pixel-packing: Specifies if pixel packing is used (in case of RGB666). "tight" = Tight packing (default value). "loose" = Loose packing. - qcom,mdss-dsi-virtual-channel-id: Specifies the virtual channel identefier. 0 = default value. - qcom,mdss-dsi-color-order: Specifies the R, G and B channel ordering. "rgb_swap_rgb" = DSI_RGB_SWAP_RGB (default value) "rgb_swap_rbg" = DSI_RGB_SWAP_RBG "rgb_swap_brg" = DSI_RGB_SWAP_BRG "rgb_swap_grb" = DSI_RGB_SWAP_GRB "rgb_swap_gbr" = DSI_RGB_SWAP_GBR - qcom,mdss-dsi-lane-0-state: Boolean that specifies whether data lane 0 is enabled. - qcom,mdss-dsi-lane-1-state: Boolean that specifies whether data lane 1 is enabled. - qcom,mdss-dsi-lane-2-state: Boolean that specifies whether data lane 2 is enabled. - qcom,mdss-dsi-lane-3-state: Boolean that specifies whether data lane 3 is enabled. - qcom,mdss-dsi-t-clk-post: Specifies the byte clock cycles after mode switch. 0x03 = default value. - qcom,mdss-dsi-t-clk-pre: Specifies the byte clock cycles before mode switch. 0x24 = default value. - qcom,mdss-dsi-stream: Specifies the packet stream to be used. 0 = stream 0 (default) 1 = stream 1 - qcom,mdss-dsi-mdp-trigger: Specifies the trigger mechanism to be used for MDP path. "none" = no trigger "trigger_te" = Tear check signal line used for trigger "trigger_sw" = Triggered by software (default) "trigger_sw_te" = Software trigger and TE - qcom,mdss-dsi-dma-trigger: Specifies the trigger mechanism to be used for DMA path. "none" = no trigger "trigger_te" = Tear check signal line used for trigger "trigger_sw" = Triggered by software (default) "trigger_sw_seof" = Software trigger and start/end of frame trigger. "trigger_sw_te" = Software trigger and TE - qcom,mdss-dsi-panel-framerate: Specifies the frame rate for the panel. 60 = 60 frames per second (default) - qcom,mdss-dsi-panel-clockrate: A 64 bit value specifies the panel clock speed in Hz. 0 = default value. - qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode panels in microseconds. Driver uses this number to adjust the clock rate according to the expected transfer time. Increasing this value would slow down the mdp processing and can result in slower performance. Decreasing this value can speed up the mdp processing, but this can also impact power consumption. As a rule this time should not be higher than the time that would be expected with the processing at the dsi link rate since anyways this would be the maximum transfer time that could be achieved. If ping pong split enabled, this time should not be higher than two times the dsi link rate time. 14000 = default value. - qcom,mdss-dsi-on-command-state: String that specifies the ctrl state for sending ON commands. "dsi_lp_mode" = DSI low power mode (default) "dsi_hs_mode" = DSI high speed mode - qcom,mdss-dsi-off-command-state: String that specifies the ctrl state for sending OFF commands. "dsi_lp_mode" = DSI low power mode (default) "dsi_hs_mode" = DSI high speed mode - qcom,mdss-dsi-post-mode-switch-on-command-state: String that specifies the ctrl state for sending ON commands post mode switch. "dsi_lp_mode" = DSI low power mode (default) "dsi_hs_mode" = DSI high speed mode - qcom,mdss-pan-physical-width-dimension: Specifies panel physical width in mm which corresponds to the physical width in the framebuffer information. - qcom,mdss-pan-physical-height-dimension: Specifies panel physical height in mm which corresponds to the physical height in the framebuffer information. - qcom,mdss-dsi-panel-mode-gpio-state: String that specifies the mode state for panel if it is defined in dsi controller. "high" = Set GPIO to HIGH "low" = Set GPIO to LOW - qcom,mdss-tear-check-disable: Boolean to disable mdp tear check. Tear check is enabled by default to avoid tearing. Other tear-check properties are ignored if this property is present. The below tear check configuration properties can be individually tuned if tear check is enabled. - qcom,mdss-tear-check-sync-cfg-height: Specifies the vertical total number of lines. The default value is 0xfff0. - qcom,mdss-tear-check-sync-init-val: Specifies the init value at which the read pointer gets loaded at vsync edge. The reader pointer refers to the line number of panel buffer that is currently being updated. The default value is panel height. - qcom,mdss-tear-check-sync-threshold-start: Allows the first ROI line write to an panel when read pointer is between the range of ROI start line and ROI start line plus this setting. The default value is 4. - qcom,mdss-tear-check-sync-threshold-continue: The minimum number of lines the write pointer needs to be above the read pointer so that it is safe to write to the panel. (This check is not done for the first ROI line write of an update) The default value is 4. - qcom,mdss-tear-check-start-pos: Specify the y position from which the start_threshold value is added and write is kicked off if the read pointer falls within that region. The default value is panel height. - qcom,mdss-tear-check-rd-ptr-trigger-intr: Specify the read pointer value at which an interrupt has to be generated. The default value is panel height + 1. - qcom,mdss-tear-check-frame-rate: Specify the value to be a real frame rate(fps) x 100 factor to tune the timing of TE simulation with more precision. The default value is 6000 with 60 fps. - qcom,mdss-dsi-reset-sequence: An array that lists the sequence of reset gpio values and sleeps Each command will have the format defined as below: --> Reset GPIO value --> Sleep value (in ms) - qcom,partial-update-enabled: Boolean used to enable partial panel update for command mode panels. - qcom,mdss-dsi-horizontal-line-idle: List of width ranges (EC - SC) in pixels indicating additional idle time in dsi clock cycles that is needed to compensate for smaller line width. - qcom,partial-update-roi-merge: Boolean indicates roi combination is need and function has been provided for dcs 2A/2B command. - qcom,dcs-cmd-by-left: Boolean to indicate that dcs command are sent through the left DSI controller only in a dual-dsi configuration - qcom,mdss-dsi-lp11-init: Boolean used to enable the DSI clocks and data lanes (low power 11) before issuing hardware reset line. - qcom,mdss-dsi-init-delay-us: Delay in microseconds(us) before performing any DSI activity in lp11 mode. This master delay (t_init_delay as per DSI spec) should be sum of DSI internal delay to reach fuctional after power up and minimum delay required by panel to reach functional. - qcom,mdss-dsi-rx-eot-ignore: Boolean used to enable ignoring end of transmission packets. - qcom,mdss-dsi-tx-eot-append: Boolean used to enable appending end of transmission packets. - qcom,ulps-enabled: Boolean to enable support for Ultra Low Power State (ULPS) mode. - qcom,suspend-ulps-enabled: Boolean to enable support for ULPS mode for panels during suspend state. - qcom,panel-roi-alignment: Specifies the panel ROI alignment restrictions on its left, top, width, height alignments and minimum width and height values - qcom,esd-check-enabled: Boolean used to enable ESD recovery feature. - qcom,mdss-dsi-panel-status-command: A byte stream formed by multiple dcs packets based on qcom dsi controller protocol, to read the panel status. This value is used to kick in the ESD recovery. byte 0: dcs data type byte 1: set to indicate this is an individual packet (no chain) byte 2: virtual channel number byte 3: expect ack from client (dcs read command) byte 4: wait number of specified ms after dcs command transmitted byte 5, 6: 16 bits length in network byte order byte 7 and beyond: number byte of payload - qcom,mdss-dsi-panel-status-command-mode: String that specifies the ctrl state for reading the panel status. "dsi_lp_mode" = DSI low power mode "dsi_hs_mode" = DSI high speed mode - qcom,mdss-dsi-panel-status-check-mode:Specifies the panel status check method for ESD recovery. "bta_check" = Uses BTA to check the panel status "reg_read" = Reads panel status register to check the panel status "reg_read_nt35596" = Reads panel status register to check the panel status for NT35596 panel. "te_signal_check" = Uses TE signal behaviour to check the panel status - qcom,mdss-dsi-panel-status-read-length: Integer value that specifies the expected read-back length of the panel register. - qcom,mdss-dsi-panel-status-value: An integer array that specifies the values of the panel status register which is used to check the panel status. The size of this array is specified by qcom,mdss-dsi-panel-status-read-length. - qcom,mdss-dsi-panel-max-error-count: Integer value that specifies the maximum number of errors from register read that can be ignored before treating that the panel has gone bad. - qcom,dynamic-mode-switch-enabled: Boolean used to mention whether panel supports dynamic switching from video mode to command mode and vice versa. - qcom,dynamic-mode-switch-type: A string specifies how to perform dynamic mode switch. If qcom,dynamic-mode-switch-enabled is set and no string specified, default value is dynamic-switch-suspend-resume. "dynamic-switch-suspend-resume"= Switch using suspend/resume. Panel will go blank during transition. "dynamic-switch-immediate"= Switch on next frame update. Panel will not go blank for this transition. "dynamic-resolution-switch-immediate"= Switch the panel resolution. Panel will not go blank for this transition. - qcom,mdss-dsi-post-mode-switch-on-command: Multiple dcs packets used for turning on DSI panel after panel has switch modes. Refer to "qcom,mdss-dsi-on-command" section for adding commands. - qcom,video-to-cmd-mode-switch-commands: List of commands that need to be sent to panel in order to switch from video mode to command mode dynamically. Refer to "qcom,mdss-dsi-on-command" section for adding commands. - qcom,cmd-to-video-mode-switch-commands: List of commands that need to be sent to panel in order to switch from command mode to video mode dynamically. Refer to "qcom,mdss-dsi-on-command" section for adding commands. - qcom,mdss-dsi-panel-orientation: String used to indicate orientation of panel "180" = panel is flipped in both horizontal and vertical directions "hflip" = panel is flipped in horizontal direction "vflip" = panel is flipped in vertical direction - qcom,panel-ack-disabled: A boolean property to indicate, whether we need to wait for any ACK from the panel for any commands that we send. - qcom,mdss-dsi-force-clock-lane-hs: Boolean to force dsi clock lanes to HS mode always. - qcom,compression-mode: Select compression mode for panel. "fbc" - frame buffer compression "dsc" - display stream compression. If "dsc" compression is used then config subnodes needs to be defined. - qcom,panel-supply-entries: A node that lists the elements of the supply used to power the DSI panel. There can be more than one instance of this binding, in which case the entry would be appended with the supply entry index. For a detailed description of fields in the supply entry, refer to the qcom,ctrl-supply-entries binding above. - qcom,config-select: Optional property to select default configuration. [[Optional config sub-nodes]] These subnodes provide different configurations for a given same panel. Default configuration can be chosen by specifying phandle of the selected subnode in the qcom,config-select. Required properties for sub-nodes: None Optional properites: - qcom,lm-split: An array of two values indicating MDP should use two layer mixers to reduce power. Ex: Normally 1080x1920 display uses single DSI and thus one layer mixer. But if we use two layer mixers then mux the output of those two mixers into single stream and route it to single DSI then we can lower the clock requirements of MDP. To use this configuration we need two fill this array with <540 540>. Both values doesn't have to be same, but recommended, however sum of both values has to be equal to the panel-width. By default two mixer streams are merged using 2D mux, however if 2 DSC encoders are used then merge is performed within compression engine. - qcom,split-mode: String property indicating which split mode MDP should use. Valid entries are "pingpong-split" and "dualctl-split". This property is mutually exclusive with qcom,lm-split. - qcom,mdss-dsc-encoders: An integer value indicating how many DSC encoders should be used to drive data stream to DSI. Default value is 1 and max value is 2. 2 encoder should be used only if qcom,mdss-lm-split or qcom,split-mode with pingpong-split is used. - qcom,mdss-dsc-slice-height: An integer value indicates the dsc slice height. - qcom,mdss-dsc-slice-width: An integer value indicates the dsc slice width. Multiple of slice width should be equal to panel-width. Maximum 2 slices per DSC encoder can be used so if 2 DSC encoders are used then minimum slice width is equal to panel-width/4. - qcom,mdss-dsc-slice-per-pkt: An integer value indicates the slice per dsi packet. - qcom,mdss-dsc-bit-per-component: An integer value indicates the bits per component before compression. - qcom,mdss-dsc-bit-per-pixel: An integer value indicates the bits per pixel after compression. - qcom,mdss-dsc-block-prediction-enable: A boolean value to enable/disable the block prediction at decoder. - qcom,mdss-dsc-config-by-manufacture-cmd: A boolean to indicates panel use manufacture command to setup pps instead of standard dcs type 0x0A. - qcom,dba-panel: Indicates whether the current panel is used as a display bridge to a non-DSI interface. - qcom,adjust-timer-wakeup-ms: An integer value to indicate the timer delay(in ms) to accommodate s/w delay while configuring the event timer wakeup logic. - qcom,mdss-dsi-display-timings: Parent node that lists the different resolutions that the panel supports. Each child represents timings settings for a specific resolution. Additional properties added to the second level nodes that represent timings properties: - qcom,mdss-dsi-timing-default: Property that specifies the current child as the default timing configuration that will be used. - qcom,mdss-dsi-timing-switch-command: List of commands that need to be sent to panel when the resolution/timing switch happens dynamically. Refer to "qcom,mdss-dsi-on-command" section for adding commands. - qcom,mdss-dsi-timing-switch-command-state: String that specifies the ctrl state for sending resolution switch commands. "dsi_lp_mode" = DSI low power mode (default) "dsi_hs_mode" = DSI high speed mode Note, if a given optional qcom,* binding is not present, then the driver will configure the default values specified. Example: &mdss_mdp { dsi_sim_vid: qcom,mdss_dsi_sim_video { qcom,mdss-dsi-panel-name = "simulator video mode dsi panel"; qcom,mdss-dsi-panel-controller = <&mdss_dsi0>; qcom,mdss-dsi-panel-height = <1280>; qcom,mdss-dsi-panel-width = <720>; qcom,mdss-dsi-bpp = <24>; qcom,mdss-dsi-pixel-packing = <0>; qcom,mdss-dsi-panel-destination = "display_1"; qcom,cmd-sync-wait-broadcast; qcom,mdss-dsi-fbc-enable; qcom,mdss-dsi-fbc-slice-height = <5>; qcom,mdss-dsi-fbc-2d-pred-mode; qcom,mdss-dsi-fbc-ver2-mode; qcom,mdss-dsi-fbc-bpp = <0>; qcom,mdss-dsi-fbc-packing = <0>; qcom,mdss-dsi-fbc-quant-error; qcom,mdss-dsi-fbc-bias = <0>; qcom,mdss-dsi-fbc-pat-mode; qcom,mdss-dsi-fbc-vlc-mode; qcom,mdss-dsi-fbc-bflc-mode; qcom,mdss-dsi-fbc-h-line-budget = <0>; qcom,mdss-dsi-fbc-budget-ctrl = <0>; qcom,mdss-dsi-fbc-block-budget = <0>; qcom,mdss-dsi-fbc-lossless-threshold = <0>; qcom,mdss-dsi-fbc-lossy-threshold = <0>; qcom,mdss-dsi-fbc-rgb-threshold = <0>; qcom,mdss-dsi-fbc-lossy-mode-idx = <0>; qcom,mdss-dsi-fbc-max-pred-err = <2>; qcom,mdss-dsi-h-front-porch = <140>; qcom,mdss-dsi-h-back-porch = <164>; qcom,mdss-dsi-h-pulse-width = <8>; qcom,mdss-dsi-h-sync-skew = <0>; qcom,mdss-dsi-v-back-porch = <6>; qcom,mdss-dsi-v-front-porch = <1>; qcom,mdss-dsi-v-pulse-width = <1>; qcom,mdss-dsi-h-left-border = <0>; qcom,mdss-dsi-h-right-border = <0>; qcom,mdss-dsi-v-top-border = <0>; qcom,mdss-dsi-v-bottom-border = <0>; qcom,mdss-dsi-border-color = <0>; qcom,mdss-dsi-underflow-color = <0xff>; qcom,mdss-dsi-bl-min-level = <1>; qcom,mdss-dsi-bl-max-level = < 15>; qcom,mdss-dsi-interleave-mode = <0>; qcom,mdss-dsi-panel-type = "dsi_video_mode"; qcom,mdss-dsi-te-check-enable; qcom,mdss-dsi-te-using-te-pin; qcom,mdss-dsi-te-dcs-command = <1>; qcom,mdss-dsi-wr-mem-continue = <0x3c>; qcom,mdss-dsi-wr-mem-start = <0x2c>; qcom,mdss-dsi-te-pin-select = <1>; qcom,mdss-dsi-h-sync-pulse = <1>; qcom,mdss-dsi-hfp-power-mode; qcom,mdss-dsi-hbp-power-mode; qcom,mdss-dsi-hsa-power-mode; qcom,mdss-dsi-bllp-eof-power-mode; qcom,mdss-dsi-bllp-power-mode; qcom,mdss-dsi-last-line-interleave; qcom,mdss-dsi-traffic-mode = <0>; qcom,mdss-dsi-virtual-channel-id = <0>; qcom,mdss-dsi-color-order = <0>; qcom,mdss-dsi-lane-0-state; qcom,mdss-dsi-lane-1-state; qcom,mdss-dsi-lane-2-state; qcom,mdss-dsi-lane-3-state; qcom,mdss-dsi-t-clk-post = <0x20>; qcom,mdss-dsi-t-clk-pre = <0x2c>; qcom,mdss-dsi-stream = <0>; qcom,mdss-dsi-mdp-trigger = <0>; qcom,mdss-dsi-dma-trigger = <0>; qcom,mdss-dsi-panel-framerate = <60>; qcom,mdss-dsi-panel-clockrate = <424000000>; qcom,mdss-mdp-transfer-time-us = <12500>; qcom,mdss-dsi-panel-timings = [7d 25 1d 00 37 33 22 27 1e 03 04 00]; qcom,mdss-dsi-panel-timings-8996 = [23 20 06 09 05 03 04 a0 23 20 06 09 05 03 04 a0 23 20 06 09 05 03 04 a0 23 20 06 09 05 03 04 a0 23 2e 06 08 05 03 04 a0]; qcom,mdss-dsi-on-command = [32 01 00 00 00 00 02 00 00 29 01 00 00 10 00 02 FF 99]; qcom,mdss-dsi-on-command-state = "dsi_lp_mode"; qcom,mdss-dsi-off-command = [22 01 00 00 00 00 00]; qcom,mdss-dsi-off-command-state = "dsi_hs_mode"; qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled"; qcom,mdss-dsi-pan-enable-dynamic-fps; qcom,mdss-dsi-pan-fps-update = "dfps_suspend_resume_mode"; qcom,min-refresh-rate = <30>; qcom,max-refresh-rate = <60>; qcom,mdss-dsi-bl-pmic-bank-select = <0>; qcom,mdss-dsi-bl-pmic-pwm-frequency = <0>; qcom,mdss-dsi-pwm-gpio = <&pm8941_mpps 5 0>; qcom,5v-boost-gpio = <&pm8994_gpios 14 0>; qcom,mdss-pan-physical-width-dimension = <60>; qcom,mdss-pan-physical-height-dimension = <140>; qcom,mdss-dsi-panel-mode-gpio-state = "low"; qcom,mdss-tear-check-sync-cfg-height = <0xfff0>; qcom,mdss-tear-check-sync-init-val = <1280>; qcom,mdss-tear-check-sync-threshold-start = <4>; qcom,mdss-tear-check-sync-threshold-continue = <4>; qcom,mdss-tear-check-start-pos = <1280>; qcom,mdss-tear-check-rd-ptr-trigger-intr = <1281>; qcom,mdss-tear-check-frame-rate = <6000>; qcom,mdss-dsi-reset-sequence = <1 2>, <0 10>, <1 10>; qcom,partial-update-enabled; qcom,dcs-cmd-by-left; qcom,mdss-dsi-lp11-init; qcom,mdss-dsi-init-delay-us = <100>; mdss-dsi-rx-eot-ignore; mdss-dsi-tx-eot-append; qcom,ulps-enabled; qcom,suspend-ulps-enabled; qcom,panel-roi-alignment = <4 4 2 2 20 20>; qcom,esd-check-enabled; qcom,mdss-dsi-panel-status-command = [06 01 00 01 05 00 02 0A 08]; qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode"; qcom,mdss-dsi-panel-status-check-mode = "reg_read"; qcom,mdss-dsi-panel-status-read-length = <8>; qcom,mdss-dsi-panel-max-error-count = <3>; qcom,mdss-dsi-panel-status-value = <0x1c 0x00 0x05 0x02 0x40 0x84 0x06 0x01>; qcom,dynamic-mode-switch-enabled; qcom,dynamic-mode-switch-type = "dynamic-switch-immediate"; qcom,mdss-dsi-post-mode-switch-on-command = [32 01 00 00 00 00 02 00 00 29 01 00 00 10 00 02 B0 03]; qcom,video-to-cmd-mode-switch-commands = [15 01 00 00 00 00 02 C2 0B 15 01 00 00 00 00 02 C2 08]; qcom,cmd-to-video-mode-switch-commands = [15 01 00 00 00 00 02 C2 03]; qcom,panel-ack-disabled; qcom,mdss-dsi-horizontal-line-idle = <0 40 256>, <40 120 128>, <128 240 64>; qcom,mdss-dsi-panel-orientation = "180" qcom,mdss-dsi-force-clock-lane-hs; qcom,compression-mode = "dsc"; qcom,adjust-timer-wakeup-ms = <1>; qcom,mdss-dsi-display-timings { wqhd { qcom,mdss-dsi-timing-default; qcom,mdss-dsi-panel-width = <720>; qcom,mdss-dsi-panel-height = <2560>; qcom,mdss-dsi-h-front-porch = <20>; qcom,mdss-dsi-h-back-porch = <8>; qcom,mdss-dsi-h-pulse-width = <8>; qcom,mdss-dsi-h-sync-skew = <0>; qcom,mdss-dsi-v-back-porch = <4>; qcom,mdss-dsi-v-front-porch = <728>; qcom,mdss-dsi-v-pulse-width = <4>; qcom,mdss-dsi-panel-framerate = <60>; qcom,mdss-dsi-panel-timings = [E6 38 26 00 68 6E 2A 3C 2C 03 04 00]; qcom,mdss-dsi-t-clk-post = <0x02>; qcom,mdss-dsi-t-clk-pre = <0x2a>; qcom,mdss-dsi-on-command = [05 01 00 00 a0 00 02 11 00 05 01 00 00 02 00 02 29 00]; qcom,mdss-dsi-on-command-state = "dsi_lp_mode"; qcom,mdss-dsi-timing-switch-command = [ 29 00 00 00 00 00 02 B0 04 29 00 00 00 00 00 02 F1 00]; qcom,mdss-dsi-timing-switch-command-state = "dsi_lp_mode"; }; }; qcom,panel-supply-entries { #address-cells = <1>; #size-cells = <0>; qcom,panel-supply-entry@0 { reg = <0>; qcom,supply-name = "vdd"; qcom,supply-min-voltage = <2800000>; qcom,supply-max-voltage = <2800000>; qcom,supply-enable-load = <100000>; qcom,supply-disable-load = <100>; qcom,supply-pre-on-sleep = <0>; qcom,supply-post-on-sleep = <0>; qcom,supply-pre-off-sleep = <0>; qcom,supply-post-off-sleep = <0>; }; qcom,panel-supply-entry@1 { reg = <1>; qcom,supply-name = "vddio"; qcom,supply-min-voltage = <1800000>; qcom,supply-max-voltage = <1800000>; qcom,supply-enable-load = <100000>; qcom,supply-disable-load = <100>; qcom,supply-pre-on-sleep = <0>; qcom,supply-post-on-sleep = <0>; qcom,supply-pre-off-sleep = <0>; qcom,supply-post-off-sleep = <0>; }; }; qcom,config-select = <&dsi_sim_vid_config0>; qcom,dba-panel; dsi_sim_vid_config0: config0 { qcom,lm-split = <360 360>; qcom,mdss-dsc-encoders = <2>; qcom,mdss-dsc-slice-height = <16>; qcom,mdss-dsc-slice-width = <360>; qcom,mdss-dsc-slice-per-pkt = <2>; qcom,mdss-dsc-bit-per-component = <8>; qcom,mdss-dsc-bit-per-pixel = <8>; qcom,mdss-dsc-block-prediction-enable; qcom,mdss-dsc-config-by-manufacture-cmd; }; dsi_sim_vid_config1: config1 { qcom,mdss-dsc-encoders = <1>; qcom,mdss-dsc-slice-height = <16>; qcom,mdss-dsc-slice-width = <360>; qcom,mdss-dsc-slice-per-pkt = <2>; qcom,mdss-dsc-bit-per-component = <8>; qcom,mdss-dsc-bit-per-pixel = <8>; qcom,mdss-dsc-block-prediction-enable; qcom,mdss-dsc-config-by-manufacture-cmd; }; dsi_sim_vid_config2: config2 { qcom,split-mode = "dualctl-split"; }; dsi_sim_vid_config3: config3 { qcom,split-mode = "pingpong-split"; }; }; };