# This file allows user to override the factory # defaults for the WLAN Driver # Enable IMPS or not gEnableImps=1 # Enable/Disable Idle Scan gEnableIdleScan=0 # Increase sleep duration (seconds) during IMPS # 0 implies no periodic wake up from IMPS. Periodic wakeup is # unnecessary if Idle Scan is disabled. gImpsModSleepTime=0 # Enable BMPS or not gEnableBmps=1 # Enable suspend or not # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter gEnableSuspend=3 # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only # 7 = 11b only 8 = 11ac only. gDot11Mode=0 # CSR Roaming Enable(1) Disable(0) gRoamingTime=0 # Assigned MAC Addresses - This will be used until NV items are in place # Each byte of MAC address is represented in Hex format as XX Intf0MacAddress=000AF58989FF Intf1MacAddress=000AF58989FE Intf2MacAddress=000AF58989FD Intf3MacAddress=000AF58989FC # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=0 InfraUapsdViSrvIntv=0 InfraUapsdBeSrvIntv=0 InfraUapsdBkSrvIntv=0 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 # Make 1x1 the default antenna configuration gNumRxAnt=1 # Beacon filtering frequency (unit in beacon intervals) gNthBeaconFilter=50 # Enable WAPI or not # WAPIIsEnabled=0 # Flags to filter Mcast abd Bcast RX packets. # Value 0: No filtering, 1: Filter all Multicast. # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast McastBcastFilter=3 #Flag to enable HostARPOffload feature or not hostArpOffload=1 #Flag to enable TCPChkSumOffld feature or not gEnableTCPChkSumOffld=1 #Flag to enable HostNSOffload feature or not hostNSOffload=1 #Flag to enable IPChkSumOffld feature or not gEnableIPChecksumOffload=0 #SoftAP Related Parameters # AP MAc addr gAPMacAddr=000AF589dcab # 802.11n Protection flag gEnableApProt=1 #Enable OBSS protection gEnableApOBSSProt=1 #Enable/Disable UAPSD for SoftAP gEnableApUapsd=1 # Fixed Rate gFixedRate=0 # Maximum Tx power # gTxPowerCap=30 # Fragmentation Threshold # gFragmentationThreshold=2346 # RTS threshold RTSThreshold=192000 # Intra-BSS forward gDisableIntraBssFwd=0 # WMM Enable/Disable WmmIsEnabled=0 # 802.11d support g11dSupportEnabled=1 # 802.11h support g11hSupportEnabled=1 # ESE Support and fast transition EseEnabled=0 ImplicitQosIsEnabled=0 gNeighborScanTimerPeriod=200 gNeighborLookupThreshold=76 gNeighborReassocThreshold=81 gNeighborScanChannelMinTime=20 gNeighborScanChannelMaxTime=30 gMaxNeighborReqTries=3 # Legacy (non-ESE, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 #Check if the AP to which we are roaming is better than current AP in terms of RSSI. #Checking is disabled if set to Zero.Otherwise it will use this value as to how better #the RSSI of the new/roamable AP should be for roaming RoamRssiDiff=3 # If the RSSI of any available candidate is better than currently associated # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without # registering for reassoc threshold). # NOTE: Value of 0 means that we would register for reassoc threshold. gImmediateRoamRssiDiff=10 # To enable, set gRoamIntraBand=1 (Roaming within band) # To disable, set gRoamIntraBand=0 (Roaming across band) gRoamIntraBand=0 # SAP Country code # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. # Example # US Indoor, USI # Korea Outdoor, KRO # Japan without optional byte, JP # France without optional byte, FR #gAPCntryCode=USI #Short Guard Interval Enable/disable gShortGI20Mhz=1 gShortGI40Mhz=1 #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled gAPAutoShutOff=0 # SAP auto channel selection configuration # 0 = disable auto channel selection # 1 = enable auto channel selection, channel provided by supplicant will be ignored gApAutoChannelSelection=0 # Listen Energy Detect Mode Configuration # Valid values 0-128 # 128 means disable Energy Detect feature # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. # 10-128 are reserved. # The EDET threshold mapping is as follows in 3dB step: # 0 = -60 dBm # 1 = -63 dBm # 2 = -66 dBm # ... # 7 = -81 dBm # 8 = -84 dBm # 9 = -87 dBm # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: # # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. # gEnablePhyAgcListenMode=128 #Preferred band (both or 2.4 only or 5 only) BandCapability=0 #Beacon Early Termination (1 = enable the BET feature, 0 = disable) enableBeaconEarlyTermination=0 beaconEarlyTerminationWakeInterval=3 #SOFTAP Channel Range selection gAPChannelSelectStartChannel=1 gAPChannelSelectEndChannel=11 #SOFTAP Channel Range selection Operating band # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND gAPChannelSelectOperatingBand=0 #Channel Bonding gChannelBondingMode5GHz=1 #Enable Keep alive with non-zero period value gStaKeepAlivePeriod = 30 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) #For both active and power save clients. #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. #If doesn't honor for 5 seconds then DUT remove client. #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period #where we send NULL frame. #gApLinkMonitorPeriod = 10 #gGoLinkMonitorPeriod = 10 #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. gGoKeepAlivePeriod = 20 gApKeepAlivePeriod = 20 #If set will start with active scan after driver load, otherwise will start with #passive scan to find out the domain gEnableBypass11d=1 #If set to 0, will not scan DFS channels gEnableDFSChnlScan=1 gVhtChannelWidth=2 gEnableLogp=1 # Enable Automatic Tx Power control gEnableAutomaticTxPowerControl=1 # 0 for OLPC 1 for CLPC and SCPC gEnableCloseLoop=1 #Data Inactivity Timeout when in powersave (in ms) gDataInactivityTimeout=200 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gEnable2x2=1 gVhtRxMCS2x2=0 gVhtTxMCS2x2=2 # Scan Timing Parameters # gPassiveMaxChannelTime=110 # gPassiveMinChannelTime=60 # gActiveMaxChannelTime=40 # gActiveMinChannelTime=20 #If set to 0, MCC is not allowed. gEnableMCCMode=1 # 1=enable STBC; 0=disable STBC gEnableRXSTBC=1 # 1=enable tx STBC; 0=disable gEnableTXSTBC=1 # 1=enable rx LDPC; 0=disable gEnableRXLDPC=1 # Enable Active mode offload gEnableActiveModeOffload=1 #Enable Scan Results Aging based on timer #Timer value is in seconds #If Set to 0 it will not enable the feature gScanAgingTime=0 #Enable Power saving mechanism Based on Android Framework #If set to 0 Driver internally control the Power saving mechanism #If set to 1 Android Framwrok control the Power saving mechanism isAndroidPsEn=0 #disable LDPC in STA mode if the AP is TXBF capable gDisableLDPCWithTxbfAP=1 #Enable thermal mitigation gThermalMitigationEnable=1 gThermalTempMinLevel1=90 gThermalTempMaxLevel0=110 gThermalTempMaxLevel1=115 gThrottlePeriod=100 gEnableFastRoamInConcurrency=1 #List of Country codes for which 11ac needs to be disabled #Each country code must be delimited by comma(,) gListOfNon11acCountryCode=RU,UA,ZA #Maxium Channel time in msec gMaxMediumTime = 6000 # 802.11K support gRrmEnable=1 gRrmOperChanMax=8 gRrmNonOperChanMax=8 gRrmRandIntvl=100 #Scan offload gEnableDirectedScanOffload=1 #FlexConnect Power Factor #Default is set to 0 (disable) gFlexConnectPowerFactor=0 #Disable split scan, the FW will take care of it gNumChanCombinedConc=60 #Enable Power Save offload gEnablePowerSaveOffload=1 #Enable firmware uart print gEnablefwprint=0 #Enable firmware log gEnablefwlog=1 #IPA config gIPAEnable=1 gIPADescSize=800 gIPAPreFilterEnable=1 gIPARMEnable=1 #P2P Listen offload gEnableP2pListenOffload=1 # Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) gVhtAmpduLenExponent=7 # Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) gVhtMpduLen=0 # Maximum number of wow filters required #gMaxWoWFilters=22 # WOW Enable/Disable. # 0 - Disable both magic pattern match and pattern byte match. # 1 - Enable magic pattern match on all interfaces. # 2 - Enable pattern byte match on all interfaces. # 3 - Enable both magic patter and pattern byte match on all interfaces. # Default value of gEnableWoW is 3. # gEnableWoW=0 # Enable or Disable MCC Adaptive Scheduler at the FW # 1=Enable (default), 0=Disable gEnableMCCAdaptiveScheduler=1 #Enable or Disable p2p device address administered isP2pDeviceAddrAdministrated=0 #Disable scan_pno by default gPNOScanSupport=0 #Enable TDLS gEnableTDLSSupport=1 # Regulatory Setting; 0=STRICT; 1=CUSTOM gRegulatoryChangeCountry=1 # Disable FW log function by default gFwDebugLogType=0 gFwDebugModuleLoglevel=0,0 # Enable or Disable Rx thread # 1=Enable (default), 0=Disable gEnableRxThread=0 # Enable or Disable FW self-recovery # Currently, It's for USB only. # 1=Enable, 0=Disable (default) gEnableFwSelfRecovery=0 # Enable or Disable SAP suspend # 1=Enable (default), 0=Disable gEnableSapSuspend=0 # Enable TxBF gTxBFEnable=1 # Enable or Disable DHCP Server offload # 1=Enable, 0=Disable (default) gDHCPServerOffloadEnable=0 # Set max number of DHCP Clients # Its value could not be greater than 10 #gDHCPMaxNumClients=10 # Set DHCP server IP # 4th field could not be greater than 99, that is xxx,xxx,xxx,0 ~ xxx,xxx,xxx,99 # 1st field could not be within the range of 224 ~ 239 (multicast IP address) #gDHCPServerIP=192,168,1,2 # gEnableSAPAuthOffload: Enable Software AP Authentication Offload feature # 1=Enable, 0=Disable (default) gEnableSAPAuthOffload=0 # gSAPAuthOffloadSec: Software AP Authentication Offload security Type, 0: disabled, 1: WPA2-PSK CCMP # gSAPAuthOffloadSec=1 # gSAPAuthOffloadKey: Passphrase of Security # gSAPAuthOffloadKey=12345678 # Enable or Disable UDP response offload feature # 1=Enable, 0=Disable (default) gudp_resp_offload_support=0 # Set UDP packet dest port # It's value is between 0 and 65535 # Default is 0 # gudp_resp_offload_dest_port=0 # Set UDP payload filter # It is only include Arabic numerals and English letter # It's length should be between 1 and 127 # gudp_resp_offload_payload_filter=require status # Set UDP response payload # It is only include Arabic numerals and English letter # It's length should be between 1 and 127 # gudp_resp_offload_response_payload=status=off # Enable or Disable WOW Pulse feature # 1 = Enable, 0 = Disable (default) gwow_pulse_support = 0 # GPIO PIN # It's value is between 0 and 255 # Default is 35 # gwow_pulse_pin = 35 # Set WOW Pulse interval low # It's value is between 160 and 480 # gwow_pulse_interval_low = 180 # Set WOW Pulse interval high # It's value is between 20 and 40 # gwow_pulse_interval_high = 20 END # Note: Configuration parser would not read anything past the END marker