91 lines
4.3 KiB
Plaintext
91 lines
4.3 KiB
Plaintext
|
Qualcomm Technologies QPNP WLED
|
||
|
|
|
||
|
|
QPNP (Qualcomm Technologies Plug N Play) WLED (White Light
|
||
|
|
Emitting Diode) driver is used for controlling display
|
||
|
|
backlight that is part of PMIC on Qualcomm Technologies
|
||
|
|
reference platforms. The PMIC is connected to the host
|
||
|
|
processor via SPMI bus.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible : should be "qcom,qpnp-wled"
|
||
|
|
- reg : base address and size for wled modules
|
||
|
|
- reg-names : names associated with base addresses. It
|
||
|
|
should be "qpnp-wled-ctrl-base", "qpnp-wled-sink-base",
|
||
|
|
"qpnp-wled-ibb-base", "qpnp-wled-lab-base".
|
||
|
|
|
||
|
|
Optional properties for WLED:
|
||
|
|
- interrupts : Specifies the interrupts associated with WLED. The available
|
||
|
|
interrupts are over voltage protection(ovp) and short circuit(sc).
|
||
|
|
The values for ovp and sc are <0x3 0xd8 0x1> and <0x3 0xd8 0x2>.
|
||
|
|
- interrupt-names : Specify the interrupt names associated with interrupts. Must be
|
||
|
|
one of "ovp-irq" or "sc-irq"
|
||
|
|
- linux,name : name of the wled. default is "wled".
|
||
|
|
- linux,default-trigger : trigger for the backlight. default is NONE.
|
||
|
|
- qcom,fdbk-output : string feedback current output for wled module. The accepted values
|
||
|
|
are "wled1", "wled2", "wled3", "wled4" and "auto". default is "auto".
|
||
|
|
- qcom,vref-mv : maximum reference voltage in mv. default is 350.
|
||
|
|
- qcom,switch-freq-khz : switch frequency in khz. default is 800.
|
||
|
|
- qcom,ovp-mv : over voltage protection value in mv. default is 17800.
|
||
|
|
- qcom,ilim-ma : maximum current limiter in ma. default is 980.
|
||
|
|
- qcom,boost-duty-ns : maximum boost duty cycle in ns. default is 104.
|
||
|
|
- qcom,mod-freq-khz : modulation frequency in khz. default is 9600.
|
||
|
|
- qcom,dim-mode : dimming mode. supporting dimming modes are "analog",
|
||
|
|
"digital", and "hybrid". default is "hybrid".
|
||
|
|
- qcom,hyb-thres : threshold value when used in hybrid mode. It represents the
|
||
|
|
percentage of brightntess at which dimming mode is switched
|
||
|
|
from "digital" to "analog". the default value is 6.25%. as the
|
||
|
|
floating point cannot be represented directly, the value is
|
||
|
|
multiplied by 100. so the default is 625.
|
||
|
|
- qcom,sync-dly-us : delay for current sync in us. default is 400.
|
||
|
|
- qcom,fs-curr-ua : maximum full scale current in ua. default is 25000.
|
||
|
|
- qcom,en-9b-dim-res : boolean, specify if 9-bit dim resultion is needed. otherwise 12-bit is used.
|
||
|
|
- qcom,en-phase-stag : boolean, specify if phase staggering is needed.
|
||
|
|
- qcom,en-cabc : boolean, specify if cabc (content adaptive backlight control) is needed.
|
||
|
|
- qcom,disp-type-amoled : specify if the display is amoled
|
||
|
|
- qcom,led-strings-list : Wled module has four strings of leds numbered from 0 to 3. each string of leds
|
||
|
|
are operated individually. specify the list of strings used by the device.
|
||
|
|
any combination of led strings can be used. default value is [00 01 02 03]
|
||
|
|
- qcom,en-ext-pfet-sc-pro : Specify if external pfet short circuit protection is needed
|
||
|
|
- qcom,cons-sync-write-delay-us : Specify in 'us' the duration of delay between two consecutive writes to
|
||
|
|
SYNC register.
|
||
|
|
|
||
|
|
Optional properties if 'qcom,disp-type-amoled' is mentioned in DT:
|
||
|
|
- qcom,loop-ea-gm : control the gm for gm stage in control loop. default is 3.
|
||
|
|
- qcom,loop-comp-res-kohm : control to select the compensation resistor in kohm. default is 320.
|
||
|
|
- qcom,vref-psm-mv : reference psm voltage in mv. default for amoled is 450.
|
||
|
|
- qcom,sc-deb-cycles : debounce time for short circuit detection
|
||
|
|
- qcom,avdd-trim-steps-from-center : The number of steps to trim the OVP threshold voltage. The possible values can be between -7 to 8.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
qcom,leds@d800 {
|
||
|
|
compatible = "qcom,qpnp-wled";
|
||
|
|
reg = <0xd800 0x100>,
|
||
|
|
<0xd900 0x100>,
|
||
|
|
<0xdc00 0x100>,
|
||
|
|
<0xde00 0x100>;
|
||
|
|
reg-names = "qpnp-wled-ctrl-base",
|
||
|
|
"qpnp-wled-sink-base",
|
||
|
|
"qpnp-wled-ibb-base",
|
||
|
|
"qpnp-wled-lab-base";
|
||
|
|
interrupts = <0x3 0xd8 0x2>;
|
||
|
|
interrupt-names = "sc-irq";
|
||
|
|
status = "okay";
|
||
|
|
linux,name = "wled";
|
||
|
|
linux,default-trigger = "bkl-trigger";
|
||
|
|
qcom,fdbk-output = "auto";
|
||
|
|
qcom,vref-mv = <350>;
|
||
|
|
qcom,switch-freq-khz = <800>;
|
||
|
|
qcom,ovp-mv = <29500>;
|
||
|
|
qcom,ilim-ma = <980>;
|
||
|
|
qcom,boost-duty-ns = <26>;
|
||
|
|
qcom,mod-freq-khz = <9600>;
|
||
|
|
qcom,dim-mode = "hybrid";
|
||
|
|
qcom,dim-method = "linear";
|
||
|
|
qcom,hyb-thres = <625>;
|
||
|
|
qcom,sync-dly-us = <800>;
|
||
|
|
qcom,fs-curr-ua = <16000>;
|
||
|
|
qcom,en-phase-stag;
|
||
|
|
qcom,led-strings-list = [00 01 02 03];
|
||
|
|
qcom,en-ext-pfet-sc-pro;
|
||
|
|
};
|