M7350/kernel/drivers/usb/dwc3/core.c

722 lines
19 KiB
C
Raw Normal View History

2024-09-09 08:52:07 +00:00
/**
* core.c - DesignWare USB3 DRD Controller Core file
*
* Copyright (C) 2010-2011 Texas Instruments Incorporated - http://www.ti.com
*
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The names of the above-listed copyright holders may not be used
* to endorse or promote products derived from this software without
* specific prior written permission.
*
* ALTERNATIVELY, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2, as published by the Free
* Software Foundation.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS
* IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
* THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
* CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
* EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
* PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
* PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
* LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
* NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/io.h>
#include <linux/list.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/of.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include "core.h"
#include "gadget.h"
#include "io.h"
#include "debug.h"
static char *maximum_speed = "super";
module_param(maximum_speed, charp, 0);
MODULE_PARM_DESC(maximum_speed, "Maximum supported speed.");
/* -------------------------------------------------------------------------- */
#define DWC3_DEVS_POSSIBLE 32
static DECLARE_BITMAP(dwc3_devs, DWC3_DEVS_POSSIBLE);
int dwc3_get_device_id(void)
{
int id;
again:
id = find_first_zero_bit(dwc3_devs, DWC3_DEVS_POSSIBLE);
if (id < DWC3_DEVS_POSSIBLE) {
int old;
old = test_and_set_bit(id, dwc3_devs);
if (old)
goto again;
} else {
pr_err("dwc3: no space for new device\n");
id = -ENOMEM;
}
return id;
}
EXPORT_SYMBOL_GPL(dwc3_get_device_id);
void dwc3_put_device_id(int id)
{
int ret;
if (id < 0)
return;
ret = test_bit(id, dwc3_devs);
WARN(!ret, "dwc3: ID %d not in use\n", id);
smp_mb__before_clear_bit();
clear_bit(id, dwc3_devs);
}
EXPORT_SYMBOL_GPL(dwc3_put_device_id);
void dwc3_set_mode(struct dwc3 *dwc, u32 mode)
{
u32 reg;
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
reg |= DWC3_GCTL_PRTCAPDIR(mode);
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
}
/**
* dwc3_core_soft_reset - Issues core soft reset and PHY reset
* @dwc: pointer to our context structure
*/
static void dwc3_core_soft_reset(struct dwc3 *dwc)
{
u32 reg;
/* Before Resetting PHY, put Core in Reset */
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg |= DWC3_GCTL_CORESOFTRESET;
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
/* Assert USB3 PHY reset */
reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
reg |= DWC3_GUSB3PIPECTL_PHYSOFTRST;
dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
/* Assert USB2 PHY reset */
reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
reg |= DWC3_GUSB2PHYCFG_PHYSOFTRST;
dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
mdelay(100);
/* Clear USB3 PHY reset */
reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
reg &= ~DWC3_GUSB3PIPECTL_PHYSOFTRST;
dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
/* Clear USB2 PHY reset */
reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
reg &= ~DWC3_GUSB2PHYCFG_PHYSOFTRST;
dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
mdelay(100);
/* After PHYs are stable we can take Core out of reset state */
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg &= ~DWC3_GCTL_CORESOFTRESET;
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
}
/**
* dwc3_free_one_event_buffer - Frees one event buffer
* @dwc: Pointer to our controller context structure
* @evt: Pointer to event buffer to be freed
*/
static void dwc3_free_one_event_buffer(struct dwc3 *dwc,
struct dwc3_event_buffer *evt)
{
dma_free_coherent(dwc->dev, evt->length, evt->buf, evt->dma);
kfree(evt);
}
/**
* dwc3_alloc_one_event_buffer - Allocates one event buffer structure
* @dwc: Pointer to our controller context structure
* @length: size of the event buffer
*
* Returns a pointer to the allocated event buffer structure on success
* otherwise ERR_PTR(errno).
*/
static struct dwc3_event_buffer *__devinit
dwc3_alloc_one_event_buffer(struct dwc3 *dwc, unsigned length)
{
struct dwc3_event_buffer *evt;
evt = kzalloc(sizeof(*evt), GFP_KERNEL);
if (!evt)
return ERR_PTR(-ENOMEM);
evt->dwc = dwc;
evt->length = length;
evt->buf = dma_alloc_coherent(dwc->dev, length,
&evt->dma, GFP_KERNEL);
if (!evt->buf) {
kfree(evt);
return ERR_PTR(-ENOMEM);
}
return evt;
}
/**
* dwc3_free_event_buffers - frees all allocated event buffers
* @dwc: Pointer to our controller context structure
*/
static void dwc3_free_event_buffers(struct dwc3 *dwc)
{
struct dwc3_event_buffer *evt;
int i;
for (i = 0; i < dwc->num_event_buffers; i++) {
evt = dwc->ev_buffs[i];
if (evt)
dwc3_free_one_event_buffer(dwc, evt);
}
kfree(dwc->ev_buffs);
}
/**
* dwc3_alloc_event_buffers - Allocates @num event buffers of size @length
* @dwc: pointer to our controller context structure
* @length: size of event buffer
*
* Returns 0 on success otherwise negative errno. In the error case, dwc
* may contain some buffers allocated but not all which were requested.
*/
static int __devinit dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length)
{
int num;
int i;
num = DWC3_NUM_INT(dwc->hwparams.hwparams1);
dwc->num_event_buffers = num;
dwc->ev_buffs = kzalloc(sizeof(*dwc->ev_buffs) * num, GFP_KERNEL);
if (!dwc->ev_buffs) {
dev_err(dwc->dev, "can't allocate event buffers array\n");
return -ENOMEM;
}
for (i = 0; i < num; i++) {
struct dwc3_event_buffer *evt;
/*
* As SW workaround, allocate 8 bytes more than size of event
* buffer given to USB Controller to avoid possible memory
* corruption caused by event buffer overflow when Hw writes
* Vendor Device test event which could be of 12 bytes.
*/
evt = dwc3_alloc_one_event_buffer(dwc, (length + 8));
if (IS_ERR(evt)) {
dev_err(dwc->dev, "can't allocate event buffer\n");
return PTR_ERR(evt);
}
dwc->ev_buffs[i] = evt;
}
return 0;
}
/**
* dwc3_event_buffers_setup - setup our allocated event buffers
* @dwc: pointer to our controller context structure
*
* Returns 0 on success otherwise negative errno.
*/
static int dwc3_event_buffers_setup(struct dwc3 *dwc)
{
struct dwc3_event_buffer *evt;
int n;
for (n = 0; n < dwc->num_event_buffers; n++) {
evt = dwc->ev_buffs[n];
dev_dbg(dwc->dev, "Event buf %p dma %08llx length %d\n",
evt->buf, (unsigned long long) evt->dma,
evt->length);
evt->lpos = 0;
dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(n),
lower_32_bits(evt->dma));
dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(n),
upper_32_bits(evt->dma));
dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(n),
(evt->length - 8) & 0xffff);
dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(n), 0);
}
return 0;
}
static void dwc3_event_buffers_cleanup(struct dwc3 *dwc)
{
struct dwc3_event_buffer *evt;
int n;
for (n = 0; n < dwc->num_event_buffers; n++) {
evt = dwc->ev_buffs[n];
evt->lpos = 0;
dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(n), 0);
dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(n), 0);
dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(n), 0);
dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(n), 0);
}
}
static void dwc3_cache_hwparams(struct dwc3 *dwc)
{
struct dwc3_hwparams *parms = &dwc->hwparams;
parms->hwparams0 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS0);
parms->hwparams1 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS1);
parms->hwparams2 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS2);
parms->hwparams3 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS3);
parms->hwparams4 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS4);
parms->hwparams5 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS5);
parms->hwparams6 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6);
parms->hwparams7 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS7);
parms->hwparams8 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS8);
}
/**
* dwc3_core_init - Low-level initialization of DWC3 Core
* @dwc: Pointer to our controller context structure
*
* Returns 0 on success otherwise negative errno.
*/
static int dwc3_core_init(struct dwc3 *dwc)
{
unsigned long timeout;
u32 reg;
int ret;
reg = dwc3_readl(dwc->regs, DWC3_GSNPSID);
/* This should read as U3 followed by revision number */
if ((reg & DWC3_GSNPSID_MASK) != 0x55330000) {
dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n");
ret = -ENODEV;
goto err0;
}
dwc->revision = reg;
/* issue device SoftReset too */
timeout = jiffies + msecs_to_jiffies(500);
dwc3_writel(dwc->regs, DWC3_DCTL, DWC3_DCTL_CSFTRST);
do {
reg = dwc3_readl(dwc->regs, DWC3_DCTL);
if (!(reg & DWC3_DCTL_CSFTRST))
break;
if (time_after(jiffies, timeout)) {
dev_err(dwc->dev, "Reset Timed Out\n");
ret = -ETIMEDOUT;
goto err0;
}
cpu_relax();
} while (true);
dwc3_core_soft_reset(dwc);
dwc3_cache_hwparams(dwc);
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
reg &= ~DWC3_GCTL_DISSCRAMBLE;
switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams1)) {
case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
reg &= ~DWC3_GCTL_DSBLCLKGTNG;
break;
default:
dev_dbg(dwc->dev, "No power optimization available\n");
}
/*
* WORKAROUND: DWC3 revisions <1.90a have a bug
* where the device can fail to connect at SuperSpeed
* and falls back to high-speed mode which causes
* the device to enter a Connect/Disconnect loop
*/
if (dwc->revision < DWC3_REVISION_190A)
reg |= DWC3_GCTL_U2RSTECN;
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
/*
* The default value of GUCTL[31:22] should be 0x8. But on cores
* revision < 2.30a, the default value is mistakenly overridden
* with 0x0. Restore the correct default value.
*/
if (dwc->revision < DWC3_REVISION_230A) {
reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
reg &= ~DWC3_GUCTL_REFCLKPER;
reg |= 0x8 << __ffs(DWC3_GUCTL_REFCLKPER);
dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
}
/*
* Currently, the default and the recommended value for GUSB3PIPECTL
* [21:19] in the RTL is 3'b100 or 32 consecutive errors. Based on
* analysis and experiments in the lab, it is found that there is a
* relatively low probability of getting 32 consecutive word errors
* in the presence of random recovered noise (during electrical idle).
* This can delay the entry to a low power state such that for
* applications where the link stays in a non-U0 state for a short
* duration (< 1 microsecond), the local PHY does not enter the low
* power state prior to receiving a potential LFPS wakeup. This causes
* the PHY CDR (Clock and Data Recovery) operation to be unstable for
* some Synopsys PHYs.
*
* The proposal now is to change the default and the recommended value
* for GUSB3PIPECTL[21:19] in the RTL from 3'b100 to a minimum of
* 3'b001. Perform the same in software for controllers prior to 2.30a
* revision.
*/
if (dwc->revision < DWC3_REVISION_230A) {
reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
reg &= ~DWC3_GUSB3PIPECTL_DELAY_P1P2P3;
reg |= 1 << __ffs(DWC3_GUSB3PIPECTL_DELAY_P1P2P3);
/*
* Receiver Detection in U3/Rx.Det is mistakenly disabled in
* cores < 2.30a. Fix it here.
*/
reg &= ~DWC3_GUSB3PIPECTL_DIS_RXDET_U3_RXDET;
dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
}
/*
* clear Elastic buffer mode in GUSBPIPE_CTRL(0) register, otherwise
* it results in high link errors and could cause SS mode transfer
* failure.
*/
reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
reg &= ~DWC3_GUSB3PIPECTL_ELASTIC_BUF_MODE;
dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
if (!dwc->ev_buffs) {
ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE);
if (ret) {
dev_err(dwc->dev, "failed to allocate event buffers\n");
ret = -ENOMEM;
goto err1;
}
}
ret = dwc3_event_buffers_setup(dwc);
if (ret) {
dev_err(dwc->dev, "failed to setup event buffers\n");
goto err1;
}
return 0;
err1:
dwc3_free_event_buffers(dwc);
err0:
return ret;
}
static void dwc3_core_exit(struct dwc3 *dwc)
{
dwc3_event_buffers_cleanup(dwc);
dwc3_free_event_buffers(dwc);
}
/* XHCI reset, resets other CORE registers as well, re-init those */
void dwc3_post_host_reset_core_init(struct dwc3 *dwc)
{
dwc3_core_init(dwc);
dwc3_gadget_restart(dwc);
}
#define DWC3_ALIGN_MASK (16 - 1)
static u64 dwc3_dma_mask = DMA_BIT_MASK(64);
static int __devinit dwc3_probe(struct platform_device *pdev)
{
struct device_node *node = pdev->dev.of_node;
struct resource *res;
struct dwc3 *dwc;
struct device *dev = &pdev->dev;
int ret = -ENOMEM;
void __iomem *regs;
void *mem;
u8 mode;
bool host_only_mode;
mem = devm_kzalloc(dev, sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
if (!mem) {
dev_err(dev, "not enough memory\n");
return -ENOMEM;
}
dwc = PTR_ALIGN(mem, DWC3_ALIGN_MASK + 1);
dwc->mem = mem;
if (!dev->dma_mask)
dev->dma_mask = &dwc3_dma_mask;
if (!dev->coherent_dma_mask)
dev->coherent_dma_mask = DMA_BIT_MASK(64);
res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!res) {
dev_err(dev, "missing IRQ\n");
return -ENODEV;
}
dwc->xhci_resources[1].start = res->start;
dwc->xhci_resources[1].end = res->end;
dwc->xhci_resources[1].flags = res->flags;
dwc->xhci_resources[1].name = res->name;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(dev, "missing memory resource\n");
return -ENODEV;
}
dwc->xhci_resources[0].start = res->start;
dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
DWC3_XHCI_REGS_END;
dwc->xhci_resources[0].flags = res->flags;
dwc->xhci_resources[0].name = res->name;
/*
* Request memory region but exclude xHCI regs,
* since it will be requested by the xhci-plat driver.
*/
res = devm_request_mem_region(dev, res->start + DWC3_GLOBALS_REGS_START,
resource_size(res) - DWC3_GLOBALS_REGS_START,
dev_name(dev));
if (!res) {
dev_err(dev, "can't request mem region\n");
return -ENOMEM;
}
regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
if (!regs) {
dev_err(dev, "ioremap failed\n");
return -ENOMEM;
}
spin_lock_init(&dwc->lock);
platform_set_drvdata(pdev, dwc);
dwc->regs = regs;
dwc->regs_size = resource_size(res);
dwc->dev = dev;
if (!strncmp("super", maximum_speed, 5))
dwc->maximum_speed = DWC3_DCFG_SUPERSPEED;
else if (!strncmp("high", maximum_speed, 4))
dwc->maximum_speed = DWC3_DCFG_HIGHSPEED;
else if (!strncmp("full", maximum_speed, 4))
dwc->maximum_speed = DWC3_DCFG_FULLSPEED1;
else if (!strncmp("low", maximum_speed, 3))
dwc->maximum_speed = DWC3_DCFG_LOWSPEED;
else
dwc->maximum_speed = DWC3_DCFG_SUPERSPEED;
dwc->needs_fifo_resize = of_property_read_bool(node, "tx-fifo-resize");
host_only_mode = of_property_read_bool(node, "host-only-mode");
pm_runtime_no_callbacks(dev);
pm_runtime_set_active(dev);
pm_runtime_enable(dev);
ret = dwc3_core_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize core\n");
return ret;
}
mode = DWC3_MODE(dwc->hwparams.hwparams0);
/* Override mode if user selects host-only config with DRD core */
if (host_only_mode && (mode == DWC3_MODE_DRD)) {
dev_dbg(dev, "host only mode selected\n");
mode = DWC3_MODE_HOST;
}
switch (mode) {
case DWC3_MODE_DEVICE:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_DEVICE);
ret = dwc3_gadget_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize gadget\n");
goto err1;
}
break;
case DWC3_MODE_HOST:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_HOST);
ret = dwc3_host_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize host\n");
goto err1;
}
break;
case DWC3_MODE_DRD:
dwc3_set_mode(dwc, DWC3_GCTL_PRTCAP_OTG);
ret = dwc3_otg_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize otg\n");
goto err1;
}
ret = dwc3_host_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize host\n");
dwc3_otg_exit(dwc);
goto err1;
}
ret = dwc3_gadget_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize gadget\n");
dwc3_host_exit(dwc);
dwc3_otg_exit(dwc);
goto err1;
}
break;
default:
dev_err(dev, "Unsupported mode of operation %d\n", mode);
goto err1;
}
dwc->mode = mode;
ret = dwc3_debugfs_init(dwc);
if (ret) {
dev_err(dev, "failed to initialize debugfs\n");
goto err2;
}
return 0;
err2:
switch (mode) {
case DWC3_MODE_DEVICE:
dwc3_gadget_exit(dwc);
break;
case DWC3_MODE_HOST:
dwc3_host_exit(dwc);
break;
case DWC3_MODE_DRD:
dwc3_gadget_exit(dwc);
dwc3_host_exit(dwc);
dwc3_otg_exit(dwc);
break;
default:
/* do nothing */
break;
}
err1:
dwc3_core_exit(dwc);
return ret;
}
static int __devexit dwc3_remove(struct platform_device *pdev)
{
struct dwc3 *dwc = platform_get_drvdata(pdev);
struct resource *res;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
pm_runtime_disable(&pdev->dev);
dwc3_debugfs_exit(dwc);
switch (dwc->mode) {
case DWC3_MODE_DEVICE:
dwc3_gadget_exit(dwc);
break;
case DWC3_MODE_HOST:
dwc3_host_exit(dwc);
break;
case DWC3_MODE_DRD:
dwc3_gadget_exit(dwc);
dwc3_host_exit(dwc);
dwc3_otg_exit(dwc);
break;
default:
/* do nothing */
break;
}
dwc3_core_exit(dwc);
return 0;
}
#ifdef CONFIG_OF
static const struct of_device_id of_dwc3_match[] = {
{
.compatible = "synopsys,dwc3"
},
{ },
};
MODULE_DEVICE_TABLE(of, of_dwc3_match);
#endif
static struct platform_driver dwc3_driver = {
.probe = dwc3_probe,
.remove = __devexit_p(dwc3_remove),
.driver = {
.name = "dwc3",
.of_match_table = of_match_ptr(of_dwc3_match),
},
};
module_platform_driver(dwc3_driver);
MODULE_ALIAS("platform:dwc3");
MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
MODULE_LICENSE("Dual BSD/GPL");
MODULE_DESCRIPTION("DesignWare USB3 DRD Controller Driver");