89 lines
2.9 KiB
Plaintext
89 lines
2.9 KiB
Plaintext
|
##### hostapd configuration file ##############################################
|
||
|
|
interface=wlan1
|
||
|
|
#bridge=bridge0
|
||
|
|
driver=nl80211
|
||
|
|
ctrl_interface=/var/run/hostapd
|
||
|
|
|
||
|
|
# SSID to be used in IEEE 802.11 management frames
|
||
|
|
ssid=QSoftAP1
|
||
|
|
|
||
|
|
# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
|
||
|
|
country_code=US
|
||
|
|
|
||
|
|
# Operation mode (1 = IEEE 802.11a, 2 = IEEE 802.11g, 4 = IEEE 802.11b,
|
||
|
|
# Default: 2 = IEEE 802.11g
|
||
|
|
wmode=1
|
||
|
|
|
||
|
|
|
||
|
|
# Channel number (IEEE 802.11)
|
||
|
|
# If auto_chan_select is set channel number is ignored
|
||
|
|
channel=36
|
||
|
|
|
||
|
|
# Best channel select (1 = Best of Channels(1,6,11), 2 = Best of Channels(1,6))
|
||
|
|
# Default value is 0
|
||
|
|
#auto_chan_select=1
|
||
|
|
|
||
|
|
# Maximum number of stations that can be connected to this interface
|
||
|
|
# Default value is 0
|
||
|
|
max_num_sta=5
|
||
|
|
|
||
|
|
# Station MAC address -based authentication
|
||
|
|
# Please note that this kind of access control requires a driver that uses
|
||
|
|
# hostapd to take care of management frame processing and as such, this can be
|
||
|
|
# used with driver=hostap or driver=nl80211, but not with driver=madwifi.
|
||
|
|
# Drivers which have support for access control can advertise the capability
|
||
|
|
# and these acl configurations are set to driver.
|
||
|
|
# 2 = accept unless in deny list
|
||
|
|
# 3 = deny unless in accept list
|
||
|
|
# 4 = use external RADIUS server (accept/deny lists are searched first)
|
||
|
|
#macaddr_acl=2
|
||
|
|
#deny_mac_file=<file>
|
||
|
|
#accept_mac_file=<file>
|
||
|
|
|
||
|
|
# Overlapping BSS scan interval configuration for HT 20/40 co-existance.
|
||
|
|
# It applies only for 2.4Ghz mode. The Default value is 300
|
||
|
|
#obss_scan_interval=300
|
||
|
|
|
||
|
|
# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535)
|
||
|
|
beacon_int=100
|
||
|
|
|
||
|
|
# Client isolation can be used to prevent low-level bridging of frames between
|
||
|
|
# associated stations in the BSS. By default, this bridging is allowed.
|
||
|
|
#ap_isolate=1
|
||
|
|
|
||
|
|
##### IEEE 802.11n related configuration ######################################
|
||
|
|
|
||
|
|
# ieee80211n: Whether IEEE 802.11n (HT) is enabled
|
||
|
|
# 0 = disabled (default)
|
||
|
|
# 1 = enabled
|
||
|
|
# Note: You will also need to enable WMM for full HT functionality.
|
||
|
|
ieee80211n=1
|
||
|
|
|
||
|
|
# HT capabilities
|
||
|
|
#ht_capab=[HT40-][HT40+][SHORT-GI-20][SHORT-GI-40]
|
||
|
|
|
||
|
|
# ht2040_coex_disable: Whether to Disable HT20/40 CoEx or not. if this
|
||
|
|
# entry is removed, it is same as the value set to 0 (i.e) HT20/40
|
||
|
|
# CoEx is enabled.
|
||
|
|
# Please note that Disabling HT20/40 CoEx is violation of standard,
|
||
|
|
# However, it is customer choice or responsiblity to enable or disable.
|
||
|
|
# Some of the customer prefers to disable even though it is not recommened
|
||
|
|
# by standard.
|
||
|
|
# 0 = enable (default)
|
||
|
|
# 1 = disable
|
||
|
|
|
||
|
|
# The station can associate again with the AP if it is still in range;
|
||
|
|
# this inactivity poll is just used as a nicer way of verifying
|
||
|
|
# inactivity; i.e., client will not report broken connection because
|
||
|
|
# disassociation frame is not sent immediately without first polling
|
||
|
|
# the STA with a data frame.
|
||
|
|
# default: 300 (i.e., 5 minutes)
|
||
|
|
#ap_max_inactivity=300
|
||
|
|
|
||
|
|
##### WPA related configuration ############################
|
||
|
|
wpa=2
|
||
|
|
wpa_key_mgmt=WPA-PSK
|
||
|
|
wpa_pairwise=CCMP
|
||
|
|
wpa_passphrase=1234567890
|
||
|
|
|